PROVISION OF DI POINT WITH APPROACH ROAD AT MT SECTION AT AF STN SURYALANKA

Amount

Surface excavation n.exc 30 cm deep and averaging 15 cm and getting out in soft/loose soil including clearing away all grass, vegetation, saplings, shrubs, brushwood, undergrowth roots and trees not exc 30cm girth complete all as specified and as directed.

Excavation in trenches, n.exc 1.5m wide and n.exc 1.5m in depth, for foundations, etc and getting out in soft/loose soil complete all as specified and as directed.

M&L for Anti-Termite Treatment to bottom and sides of excavation at the rate of 5 litres of emulsion per sqare metre of surface area complete all as specified and as directed.

M&L for Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregates as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for Reinforced cement concrete M-30 using 20mm graded stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for Reinforced cement concrete M-30 using 20mm graded stone aggregates as in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for Anti-Termite Treatment to back fill in contact with foundation at the rate of 7.50 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with back fill to be measured) complete all as specified and as directed.

M&L of Reinforced cement concrete M-30 using 20mm graded stone aggregates as in Beams, Cantilevers, bressumers, lintels over 1.50m span complete all as specified and as directed.

M&L of Reinforced cement concrete M-30 using 20mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roof, landings, balconies, deck slabs and in shelves and like complete all as specified and as directed.

M&L of Reinforced cement concrete M-30 using 20mm graded stone aggregates as in Chajjas complete all as specified and as directed.

S&F for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed.

All as per item No.11 above but 6 to 8mm dia complete all as specified and as directed.

All as per item No.11 above but 5mm dia and over upto and including 10mm dia as in stirrups, spacres and binders complete all as specified and as directed.

M&L for Steel formwork to sedes of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter with rough finished surfaces of concrete complete all as specified and as directed.

M&L for Steel formwork to sedes of pillars, posts, struts, piers, columns and stanchions with rough finished surfaces of concrete complete all as specified and as directed.

M&L for Steel formwork to sedes and soffits of floor or roof beams, beam haunchings, lintels, shelves including supports, overhangs etc complete with rough finished surfaces of concrete complete all as specified and as directed.

M&L for Steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, n.exc 200mm thick (Horizontal or slop) with rough finished surfaces of concrete complete all as specified and as directed.

M&L for Steel formwork to Chullah hoods, chajjas, troughs and similar items including edges etc complete with rough finished surfaces of concrete complete all as specified and as directed.

M&L for Steel formwork to edges of concrete flats, trads, floor and roofs n.exc 20cm wide and window cills etc complete with rough finished surfaces of concrete complete all as specified and as directed.

M&L for Plain cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregates as in damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed.

M&L for Old size burnt brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for Anti-Termite Treatment to Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre complete all as specified and as directed.

M&L for Anti-Termite Treatment to Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for Broken stone hard core of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed complete all as specified and as directed.

M&L for 100mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregates as in sub base of floor complete all as specified and as directed.

M&L for 50mm thick plain cement concrete 1:2:4 typeB-1 using 20mm graded stone aggregates as in sub base of floor complete all as specified and as directed.

M&L for 25mm thick plain cement concrete 1:2:4type B-0 using 25mm graded stone aggregates as in sub base of floor complete all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregates as in Plinth Protection complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 10mm thick light shade (square/ rectangular) area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 10mm thick light shade in vertical surfaces as in dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10 mm thick screed in cement mortar 1:4 complete all as specified and as directed.

M&L for rendering 5mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling surface finished even and smooth with out using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick or concrete in CM 1:6 finishing even and smooth with out using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in two layers, first layer 10 mm thick in CM 1:6 and second layer 5 mm thick in CM 1:4 finishing fair and even mixed with WPC as per manufacturer's instructions all as specified and directed. (Note : Supply of water proofing compound shall be measured and paid separately) complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall, finishing walls with Acrylic smooth exterior paint of required shade : New work (two or more coats applied @ 1.67ltr/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) including preparation of surfaces complete complete all as specified and as directed.

M&L for powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc., complete all as specified and as directed.

S&F for Powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screws complete all as specified and as directed.

S&F of powder coated anodised aluminium window and ventilator glazed shutters, side hung type without sash bars aluminium sections weighing 0.55 kg/m (standard aluminium section of DG-2496 of sizes 39.4 x 17.7 mm and 1.2 mm thick (min) including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21, 100mm long (2Nos), suitable handle (1Nos) for each shutter complete all as specified and as directed.

S&F of 4 mm thick Sheet Glass, ordinary quality and glazing with aluminium beads complete all as specified and as directed.

S&F of 4 mm thick Figured glass, pin head type and glazing with aluminium beads complete all as specified and as directed..

M&L 19mm thick pre laminated particle board exrior grade, both side pre-laminated with decorative choice laminations fixed with screws or necessary cleats as in aluminium shutters complete all as specified and directed

S&F for Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length cover plate 1500 complete all as specified and as directed.

S&F for Aluminium extruded section Door closer hydraulically regulated, designation No.2, universal type, suitable for door shutter of 701 to 850mm in width and of weight between 36 to 60kg and fixed complete all as specified and as directed.

S&F of curtain rods (drapery rods) not less than 25 mm dia, anodised aluminium alloy with fixing brackets fixed in repairs complete all as specified and as directed.

Returning , filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soil/loose soil complete all as specified and as directed.

Removing excavated materials not exceeding 50m and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar 1:3 on roof/ concrete surfaces with using water proofing compound as per manufacturer's instructions, surface finished even and smooth without using extra cement complete all as specified and as directed. (Supply only of water proofing compound/admixture shall be measured and paid separately).

M&L for water proofing treatment with 4mm thick APP modified membrane weighing not less than 4Kg/Sqm reinforced with non woven polyester matt weighing not less than 160 Gram/Sqm having softening point not less than 140 degree Celsius, longitudinal tensile strength not less than 300 N/Sqm, tearing strength of 180 N, laid after applying a coat of Bitumen Emulsion, Primer @ 0.20Kg/Sqm over the thoroughly cleaned surfaces to be water proofed. Membrane shall then be laid with 10Cm side overlaps and 15Cm end laps completely thermo fused by flame torch application as per manufacturer's instructions. Care shall be taken to avoid wrinkles while sticking the membrane on the bitumen surface. A coat of hot blown bitumen 90/15 shall be applied on top of the membrane @ 1.20 Kg/Sqm and finally finished with solar reflective aluminium paint @ 0.10 Kg/Sqm. The water proofing membrane shall be extended upto a height of minimum 30 cm on wall and inserted by cutting groove and filling with bitumen complete all as specified and as directed.

Supply only of integral water proofing compound of approved make complete all as specified and as directed.

S&F for 4levers brass Mortice lock vertical type, size 100mm etc complete all as specified and as directed.

S&F of 20 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., complete all as specified and as directed.

S&F of 25 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections complete all as specified and as directed.

S&F in repairs of 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs Vitreous China wash basin, white, flat back, of size 550x400 mm excluding taps, waste chain and plug and porcelain stopper but including brackets and brass, 32 mm dia chromium plated waste fitting and 40 mm bore PVC waste pipe complete all as specified and as directed.

S&F of CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed.

S&F of PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

S&F of Towel rail 600 mm long of PTMT minimum weight 190 gms, fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and as directed.

S&F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in floors as in soil, waste and pipes complete all as specified and as directed.

S&F of 75 mm bore PVC (SWR) bends any radius provided with access door, complete all as specified and as directed.

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement , fixed in repairs complete all as specified and as directed.

M&L for Hard core of gauge n.exc 63 mm , with broken stone or boulders , deposited, spread and levelled in layers n.exc 15 cm thick, watered and well rammed to a true surface complete all as specified and as directed.

M&L for for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregates as in sub base of hard standing complete all as specified and as directed.

M&L for Palin cement concrete 1:3:6 mix type C-1 as in bed block, kerbs, copings etc, including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L sand filling under floors or in foundations including watering and consolidation in two or three layers complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M35 grade with grey cement and pigment complete all as specified and as directed.

M&L for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits) with 1.5 sqmm nominal cross-sectional area, single core PVC insulated (FRLS), unsheathed multistranded copper conductor cable 1100 Volts grade drawn through and including rigid non-metallic PVC concealed conduit 20mm dia medium grade and accessories ISI marked and suitable modular pressed steel terminal boxes 1.6mm thick (recessed), sockets etc including 1.5 Sqmm nominal cross sectional area, single core PVC insulated (FRLS), unsheathed multistranded copper conductor cable earth continuity wire to common earth and connected to earth dolly for one light / fan/ Security light/ 5Amps Indp Socket / Bell point controlled by one switch complete all as specified and as directed.

All as per Item No. 2 above but one 3 pin socket outlet, 15 amps / AC Metal Clad, controlled by one switch on independent board with 4 sqmm size cable for Phase, neutral and earth complete all as specified and as directed.

S&F in repairs Modular Switch 5/6 Amps, 1module 1 Way complete all as specified and as directed.

S&F in repairs Modular Switch 15/16 Amps, 1 Module 1 Way complete all as specified and as directed.

S&F in repair Modular Socket 5/6 Amps, 2 Module 2 and 3 pin complete all as specified and as directed.

S&F in repair Modular Socket 15/16 Amps, 2 Module 2/3 pin complete all as specified and as directed.

S&F in repair Modular Fan Regulator Step type, 2 Module 120W complete all as specified and as directed.

S&F in repair 3 Module Cover Plate with frame and Metal Flush Box complete all as specified and as directed.

S&F in repairs 8 Module Cover Plate with frame and Metal Flush complete all as specified and as directed.

S&F in repair Ceiling rose, 3 plate /PVC/ polycarbonate, isolated body complete all as specified and as directed

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and as directed.

S&F in repair LED lights fitting 1x 20W, 4 Feet 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F in repair LED Bldg. Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

S&F in repairs street light brackets made of 25 mm dia G.I. Pipe light grade in shape and angle as directed not exceeding 1.5 mtrs in length fixed to wall with suitable size of M.S. flat iron clamps, M.S nut & bolt with cup washers, painting to MS material with anti corrosive paint complete all as specified and as directed.

Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete all as specified and as directed.

S&F SPN DB Double door 8 way with tray for provision of MCBs, and Dolly for earth and natural complete all as specified and as directed.

S&F MCB Two Pole 6-32 Amps, 10 kA, C Curve complete all as specified and as directed.

S&F MCB Single Pole 6-32 Amps, 10 kA, C Curve complete all as specified and as directed.

M&L Earthing complete with earth galvanized steel plate electrode 600x600x6mm buried directly in ground earth pit not less than 2.25 mtr below ground level with top edge of the plate not less than 1.5 mtr below ground level, surrounded from all sides with mixture of charcoal and common salt and electrode connected with galvanized earth lead GI wire 4 mm dia by means of bolts, check nut and washers of GI or steel, GI pipe light grade of 15 mm bore as protection pipe, GI wire of length not more than 7.5 mtr and connected to test point. GI pipe 20mm dia light grade for watering, funnel with wire mesh, PCC pit and RCC (1:2:4) type B-1 for cover with 8 mm dia bar reinforcement both ways @ 140 c/c including excavation and earth work disposal of surplus soil to a distance not exceeding 50 mtr as shown on electrical plate No 3 of SSR 2009 complete all as specified and as directed.

S&F in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with blades,and frame and louver complete all as specified and as directed.

Supply and lay in repairs 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801, PP-R pipes SDR 7.4 (PN-16) and PP-R plain plain and brass threaded fittings laid in concealed work complete of size outer dia 32 mm complete all as specified and as directed.

Supply and fix PPR Gate Valves (Brass Insert) of outer dia 32 mm complete all as specified and as directed.

Cutting DI/ERW/ GI/ UPVC / PPR pipe of any bore upto 80 mm dia and reducing to required length before laying and insertion of 'T's and branches for 50 mm/ 25 mm bore dia complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of 2.0 core 16 Sqmm complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for laying of cable n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft / loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

S&L Sand filling for cable protection above and below cable and rammed down complete all as specified and as directed

S&L Red Bricks common burnt clay building bricks, sub-class ‘B’ designation 75 complete all as specified and as directed.

S&L GI pipe light grade for cable protection with clamps of size not less than 40 mm dia complete all as specified and as directed.

DHANA CONSTRUCTIONS