Establishing the Advanced Centre for Regenerative Medicine and Stem Cells Research in Cutaneous Biology (AcREM-STEM) at Kariavattom Campus - Lab Furniture.

Amount

Main Laboratory

od314725/2023_2024 : TABLE MAIN 1500W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323347/2023_2024 : TABLE ADDON 1500W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.

od323370/2023_2024 : UNDERBENCH CABINET 600W-450D-674H 2S 1D<br>WELDED UNDER-BENCH STORAGE CABINETS<br>Under bench cabinets are to be Pure epoxy powder coated with thickness of 40-60 microns and should be suspended from tubular structure. The cabinet should have a corrosion resistance magnetic strip as shutter catch, shutter and drawer are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are to be of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet.<br>Unit Construction: It should be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm and drawer separator should be of 1.2mm thick.<br>Shelf: Should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. <br>Shutter should be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound dampening.<br>Drawer: Should be welded single piece construction with over-closing sandwich drawer front filled with 15mm thick paper honeycomb for sound dampening.<br>Units should be in 450mm and 600mm widths.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323462/2023_2024 : REAGENT SHELF ISLAND MAIN 1500W<br>Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post should have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. Welded frames to be screw fitted between two posts and to be made of 1.2 mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. The shelves can be removed for cleaning purpose. A total depth of reagent shelves to be maintained at 150mm for wall benches and 300mm for island benches. Reagent shelves modules to have electrical book and having cutouts for electrical switches and sockets.

od323469/2023_2024 : REAGENT SHELF ISLAND ADDON 1200W<br>Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post should have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. Welded frames to be screw fitted between two posts and to be made of 1.2 mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. The shelves can be removed for cleaning purpose. A total depth of reagent shelves to be maintained at 150mm for wall benches and 300mm for island benches. Reagent shelves modules to have electrical book and having cutouts for electrical switches and sockets.

od323473/2023_2024 : LEG SPACE PANEL SET 900W-900H<br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.

od323482/2023_2024 : ISLAND SIDE PANEL SET 1500W-900HCOVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323504/2023_2024 : Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D)<br>LABORATORY SINK AND ACCESSORIES<br>Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size to be a minimum of (L x W x D) 560 x 355 x 200 mm. Faucet should be 3-way type faucet of reputed make (Ex. Premier Polymer)<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323510/2023_2024 : 3 Way Water Faucet Bench Mounted, 8"" Swing Gooseneck Model No. 100/32<br>SERVICE FITTINGS AND ACCESSORIES<br>Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323512/2023_2024 : "Emergency Eye Wash - 2 Way, Deck Mounted (Drench Hose Unit) With Braided Stainless Steel Hose Model No. 100-36<br>GENERAL - Provide emergency eye, eye/face wash, safety stations and drench hose units with spray-type outlet heads to deliver a soft, wide, high-volume spray of water. Outlet heads should have an internal self-regulating flow control, a reticulated polyurethane filter, a threaded spray cover and a hinged swing-away dust cover. Hinged cover should be permanently attached to outlet head body with a stainless-steel pin. All wearing components should be located inside spray head for ease of service. All emergency eye wash and shower equipment should be third-party certified to comply with ANSI Z358.1-2009.<br>DECK-MOUNTED EYE-WASH - Deck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass self-closing type with a stainless-steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose."<br><br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323514/2023_2024 : Ss Pegboard 550X420X55, 25 pegs<br>These should be Single faced high grade stainless steel pegboard having a tray hole for water drainage and detachable pegs. The essence should be made up of I mm thick stainless steel (SS 304) whereas the pegs should be made up of polypropylene and should be adjustable with a minimum 10mm distance between each peg<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323515/2023_2024 : Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk<br>WORKTOP<br>It should be 20mm (+/- 2mm) thick Mobil Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 25 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. A representation the worktop edges is shown as under<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323546/2023_2024 : 3 Module Plate - Model No: Cs933M

od323547/2023_2024 : 6/16A, 6 Pin Shutter Socket - Model No: M1332

od323548/2023_2024 : 16A, 1 Way Switch - Model No: M0130

od323549/2023_2024 : Anti-Siphon Bottle Trap Model : S 04 Make: Premier

od323550/2023_2024 : Flexible/F Serated Connector Model : Hp 01 Make: Premier

od323551/2023_2024 : 6 MM Self Adhesive Natural Rubber Strip

od323552/2023_2024 : Masking Tape

od323553/2023_2024 : Silicon Sealant - Black

od323554/2023_2024 : Bracket for island table

Tissue Culture Lab Work Bench 1 (2540mm X 1500mm)

od323955/2023_2024 : TABLE MAIN 1200W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating. Approved Make Godrej Interio / Haworth / Hermen Miller

od324189/2023_2024 : TABLE ADDON 1200W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323370/2023_2024 : UNDERBENCH CABINET 600W-450D-674H 2S 1D<br>WELDED UNDER-BENCH STORAGE CABINETS<br>Under bench cabinets are to be Pure epoxy powder coated with thickness of 40-60 microns and should be suspended from tubular structure. The cabinet should have a corrosion resistance magnetic strip as shutter catch, shutter and drawer are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are to be of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet.<br>Unit Construction: It should be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm and drawer separator should be of 1.2mm thick.<br>Shelf: Should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. <br>Shutter should be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound dampening.<br>Drawer: Should be welded single piece construction with over-closing sandwich drawer front filled with 15mm thick paper honeycomb for sound dampening.<br>Units should be in 450mm and 600mm widths.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od324687/2023_2024 : REAGENT SHELF ISLAND MAIN 1200W<br>Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post should have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. Welded frames to be screw fitted between two posts and to be made of 1.2 mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. The shelves can be removed for cleaning purpose. A total depth of reagent shelves to be maintained at 150mm for wall benches and 300mm for island benches. Reagent shelves modules to have electrical book and having cutouts for electrical switches and sockets.<br><br>Approved Make Godrej Interio / Haworth / Hermen Miller

od325571/2023_2024 : REAGENT SHELF ISLAND ADDON 600W<br>Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post should have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. Welded frames to be screw fitted between two posts and to be made of 1.2 mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. The shelves can be removed for cleaning purpose. A total depth of reagent shelves to be maintained at 150mm for wall benches and 300mm for island benches. Reagent shelves modules to have electrical book and having cutouts for electrical switches and sockets.<br><br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323482/2023_2024 : ISLAND SIDE PANEL SET 1500W-900HCOVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323504/2023_2024 : Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D)<br>LABORATORY SINK AND ACCESSORIES<br>Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size to be a minimum of (L x W x D) 560 x 355 x 200 mm. Faucet should be 3-way type faucet of reputed make (Ex. Premier Polymer)<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323510/2023_2024 : 3 Way Water Faucet Bench Mounted, 8"" Swing Gooseneck Model No. 100/32<br>SERVICE FITTINGS AND ACCESSORIES<br>Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323512/2023_2024 : "Emergency Eye Wash - 2 Way, Deck Mounted (Drench Hose Unit) With Braided Stainless Steel Hose Model No. 100-36<br>GENERAL - Provide emergency eye, eye/face wash, safety stations and drench hose units with spray-type outlet heads to deliver a soft, wide, high-volume spray of water. Outlet heads should have an internal self-regulating flow control, a reticulated polyurethane filter, a threaded spray cover and a hinged swing-away dust cover. Hinged cover should be permanently attached to outlet head body with a stainless-steel pin. All wearing components should be located inside spray head for ease of service. All emergency eye wash and shower equipment should be third-party certified to comply with ANSI Z358.1-2009.<br>DECK-MOUNTED EYE-WASH - Deck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass self-closing type with a stainless-steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose."<br><br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323514/2023_2024 : Ss Pegboard 550X420X55, 25 pegs<br>These should be Single faced high grade stainless steel pegboard having a tray hole for water drainage and detachable pegs. The essence should be made up of I mm thick stainless steel (SS 304) whereas the pegs should be made up of polypropylene and should be adjustable with a minimum 10mm distance between each peg<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323515/2023_2024 : Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk<br>WORKTOP<br>It should be 20mm (+/- 2mm) thick Mobil Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 25 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. A representation the worktop edges is shown as under<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od325928/2023_2024 : WALL CABINET 600W-320D-674H 2S<br>The construction should be the same as the under-bench cabinets. The height of these cabinets should be around 635mm while the depth should be around 340mm. The shutters should be available in two options: Metal shutters and Metal frame with in serted glass. There should be one height-adjustable shelf inside each cabinet. Other construction should be similar to under-bench cabinet<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323554/2023_2024 : Bracket for island table

od323553/2023_2024 : Silicon Sealant - Black

od323552/2023_2024 : Masking Tape

od323551/2023_2024 : 6 MM Self Adhesive Natural Rubber Strip

od323550/2023_2024 : Flexible/F Serated Connector Model : Hp 01 Make: Premier

od323549/2023_2024 : Anti-Siphon Bottle Trap Model : S 04 Make: Premier

od323548/2023_2024 : 16A, 1 Way Switch - Model No: M0130

od323547/2023_2024 : 6/16A, 6 Pin Shutter Socket - Model No: M1332

od323546/2023_2024 : 3 Module Plate - Model No: Cs933M

Tissue Cclture Lab Work Bench 2 (2540mm x 1500mm)

od323955/2023_2024 : TABLE MAIN 1200W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating. Approved Make Godrej Interio / Haworth / Hermen Miller

od324189/2023_2024 : TABLE ADDON 1200W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323370/2023_2024 : UNDERBENCH CABINET 600W-450D-674H 2S 1D<br>WELDED UNDER-BENCH STORAGE CABINETS<br>Under bench cabinets are to be Pure epoxy powder coated with thickness of 40-60 microns and should be suspended from tubular structure. The cabinet should have a corrosion resistance magnetic strip as shutter catch, shutter and drawer are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are to be of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet.<br>Unit Construction: It should be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm and drawer separator should be of 1.2mm thick.<br>Shelf: Should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. <br>Shutter should be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound dampening.<br>Drawer: Should be welded single piece construction with over-closing sandwich drawer front filled with 15mm thick paper honeycomb for sound dampening.<br>Units should be in 450mm and 600mm widths.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od324687/2023_2024 : REAGENT SHELF ISLAND MAIN 1200W<br>Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post should have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. Welded frames to be screw fitted between two posts and to be made of 1.2 mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. The shelves can be removed for cleaning purpose. A total depth of reagent shelves to be maintained at 150mm for wall benches and 300mm for island benches. Reagent shelves modules to have electrical book and having cutouts for electrical switches and sockets.<br><br>Approved Make Godrej Interio / Haworth / Hermen Miller

od325571/2023_2024 : REAGENT SHELF ISLAND ADDON 600W<br>Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post should have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. Welded frames to be screw fitted between two posts and to be made of 1.2 mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. The shelves can be removed for cleaning purpose. A total depth of reagent shelves to be maintained at 150mm for wall benches and 300mm for island benches. Reagent shelves modules to have electrical book and having cutouts for electrical switches and sockets.<br><br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323482/2023_2024 : ISLAND SIDE PANEL SET 1500W-900HCOVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323504/2023_2024 : Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D)<br>LABORATORY SINK AND ACCESSORIES<br>Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size to be a minimum of (L x W x D) 560 x 355 x 200 mm. Faucet should be 3-way type faucet of reputed make (Ex. Premier Polymer)<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323510/2023_2024 : 3 Way Water Faucet Bench Mounted, 8"" Swing Gooseneck Model No. 100/32<br>SERVICE FITTINGS AND ACCESSORIES<br>Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323512/2023_2024 : "Emergency Eye Wash - 2 Way, Deck Mounted (Drench Hose Unit) With Braided Stainless Steel Hose Model No. 100-36<br>GENERAL - Provide emergency eye, eye/face wash, safety stations and drench hose units with spray-type outlet heads to deliver a soft, wide, high-volume spray of water. Outlet heads should have an internal self-regulating flow control, a reticulated polyurethane filter, a threaded spray cover and a hinged swing-away dust cover. Hinged cover should be permanently attached to outlet head body with a stainless-steel pin. All wearing components should be located inside spray head for ease of service. All emergency eye wash and shower equipment should be third-party certified to comply with ANSI Z358.1-2009.<br>DECK-MOUNTED EYE-WASH - Deck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass self-closing type with a stainless-steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose."<br><br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323514/2023_2024 : Ss Pegboard 550X420X55, 25 pegs<br>These should be Single faced high grade stainless steel pegboard having a tray hole for water drainage and detachable pegs. The essence should be made up of I mm thick stainless steel (SS 304) whereas the pegs should be made up of polypropylene and should be adjustable with a minimum 10mm distance between each peg<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323515/2023_2024 : Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk<br>WORKTOP<br>It should be 20mm (+/- 2mm) thick Mobil Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 25 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. A representation the worktop edges is shown as under<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od325928/2023_2024 : WALL CABINET 600W-320D-674H 2S<br>The construction should be the same as the under-bench cabinets. The height of these cabinets should be around 635mm while the depth should be around 340mm. The shutters should be available in two options: Metal shutters and Metal frame with in serted glass. There should be one height-adjustable shelf inside each cabinet. Other construction should be similar to under-bench cabinet<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323554/2023_2024 : Bracket for island table

od323553/2023_2024 : Silicon Sealant - Black

od323552/2023_2024 : Masking Tape

od323551/2023_2024 : 6 MM Self Adhesive Natural Rubber Strip

od323550/2023_2024 : Flexible/F Serated Connector Model : Hp 01 Make: Premier

od323549/2023_2024 : Anti-Siphon Bottle Trap Model : S 04 Make: Premier

od323548/2023_2024 : 16A, 1 Way Switch - Model No: M0130

od323547/2023_2024 : 6/16A, 6 Pin Shutter Socket - Model No: M1332

od323546/2023_2024 : 3 Module Plate - Model No: Cs933M

Main Laboratory Work Bench 2 (3770mm x 1500mm)

od314725/2023_2024 : TABLE MAIN 1500W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od316544/2023_2024 : TABLE ADDON 600W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.

od323347/2023_2024 : TABLE ADDON 1500W-750D-900H<br>D-FRAME SYSTEM<br>All D-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.<br>The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus.<br>Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish.<br>The D-Frames structure should be for suspended storage cabinets <br>HORIZONTAL MEMBERS <br>These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500. <br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.

od323370/2023_2024 : UNDERBENCH CABINET 600W-450D-674H 2S 1D<br>WELDED UNDER-BENCH STORAGE CABINETS<br>Under bench cabinets are to be Pure epoxy powder coated with thickness of 40-60 microns and should be suspended from tubular structure. The cabinet should have a corrosion resistance magnetic strip as shutter catch, shutter and drawer are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are to be of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet.<br>Unit Construction: It should be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm and drawer separator should be of 1.2mm thick.<br>Shelf: Should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. <br>Shutter should be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound dampening.<br>Drawer: Should be welded single piece construction with over-closing sandwich drawer front filled with 15mm thick paper honeycomb for sound dampening.<br>Units should be in 450mm and 600mm widths.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323462/2023_2024 : REAGENT SHELF ISLAND MAIN 1500W<br>Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post should have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. Welded frames to be screw fitted between two posts and to be made of 1.2 mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. The shelves can be removed for cleaning purpose. A total depth of reagent shelves to be maintained at 150mm for wall benches and 300mm for island benches. Reagent shelves modules to have electrical book and having cutouts for electrical switches and sockets.

od323469/2023_2024 : REAGENT SHELF ISLAND ADDON 1200W<br>Fixed-Type reagent shelves should be provided. It should be complete modular design consisting of 2 stage horizontal storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post should have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. Welded frames to be screw fitted between two posts and to be made of 1.2 mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. The shelves can be removed for cleaning purpose. A total depth of reagent shelves to be maintained at 150mm for wall benches and 300mm for island benches. Reagent shelves modules to have electrical book and having cutouts for electrical switches and sockets.

od323473/2023_2024 : LEG SPACE PANEL SET 900W-900H<br>COVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.

od323482/2023_2024 : ISLAND SIDE PANEL SET 1500W-900HCOVER PANELS<br>All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323504/2023_2024 : Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D)<br>LABORATORY SINK AND ACCESSORIES<br>Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size to be a minimum of (L x W x D) 560 x 355 x 200 mm. Faucet should be 3-way type faucet of reputed make (Ex. Premier Polymer)<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323510/2023_2024 : 3 Way Water Faucet Bench Mounted, 8"" Swing Gooseneck Model No. 100/32<br>SERVICE FITTINGS AND ACCESSORIES<br>Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323512/2023_2024 : "Emergency Eye Wash - 2 Way, Deck Mounted (Drench Hose Unit) With Braided Stainless Steel Hose Model No. 100-36<br>GENERAL - Provide emergency eye, eye/face wash, safety stations and drench hose units with spray-type outlet heads to deliver a soft, wide, high-volume spray of water. Outlet heads should have an internal self-regulating flow control, a reticulated polyurethane filter, a threaded spray cover and a hinged swing-away dust cover. Hinged cover should be permanently attached to outlet head body with a stainless-steel pin. All wearing components should be located inside spray head for ease of service. All emergency eye wash and shower equipment should be third-party certified to comply with ANSI Z358.1-2009.<br>DECK-MOUNTED EYE-WASH - Deck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass self-closing type with a stainless-steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose."<br><br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323514/2023_2024 : Ss Pegboard 550X420X55, 25 pegs<br>These should be Single faced high grade stainless steel pegboard having a tray hole for water drainage and detachable pegs. The essence should be made up of I mm thick stainless steel (SS 304) whereas the pegs should be made up of polypropylene and should be adjustable with a minimum 10mm distance between each peg<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323515/2023_2024 : Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk<br>WORKTOP<br>It should be 20mm (+/- 2mm) thick Mobil Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 25 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. A representation the worktop edges is shown as under<br>Approved Make Godrej Interio / Haworth / Hermen Miller

od323554/2023_2024 : Bracket for island table

od323553/2023_2024 : Silicon Sealant - Black

od323552/2023_2024 : Masking Tape

od323551/2023_2024 : 6 MM Self Adhesive Natural Rubber Strip

od323550/2023_2024 : Flexible/F Serated Connector Model : Hp 01 Make: Premier

od323549/2023_2024 : Anti-Siphon Bottle Trap Model : S 04 Make: Premier

od323548/2023_2024 : 16A, 1 Way Switch - Model No: M0130

od323547/2023_2024 : 6/16A, 6 Pin Shutter Socket - Model No: M1332

od323546/2023_2024 : 3 Module Plate - Model No: Cs933M

Forte Storage Solutions

Bidder Name

Forte Storage Solutions

M/s LUCRUM VENTURES