Fabrication Tenders in Jharkhand

Damaged 10/8in dia pipe line different place of mine premises to 1T Deco coal face for repairing of damaged pipe line through cutting and welding for further laying and jointing of 10/8in dia MS Pipe line and installation of 4000GPM pump 1T Deco coal

1.Repairing of stick assly. Broken eye and housing welding grinding and line boring its steel bush pin Ck 300 768.2.Repairing of under carriage (H frame) chassis of CK 300 Shovel SL No 768 3.Repairing of transmission pump of Tata Hitachi Shovel Sl 18

Removal of Broken bolts and re-threading of sprocket and TC Guard and Re-developing of worn out eye hole and line boring with new bush providing and fitting and pin welding and machining and repairing of H-Link spacer guide of Tata Hitachi Shovel No.

shifting of 2nd pump of 1000 GPM, Make - Kirloskar oil engines Itd. from one place to other place within 40 mtrs. radius, due to increased water level in sump also Laying and welding of 8 inch dia. 30 mtrs, pipeline new extension near pump 34 delive

Cutting and welding of damaged 8 inch dia G.I. Pipes to make Short Pieces and Bends and supply and providing of one no. 8 inch dia Jetting Hose Pipe, required for changing the location of Pumps as and when required in Mine, w.r.t. Karo OCP, under BnK

Rep.of crusher roll of F/B No-5 along with cutting and welding of picks with holder,dism. and fitting of crusher drum, grooving and grinding of the crusher roll, rep.of drive shaft and replacement of wornout sleeve bush and checknut,F/B No-5,AMPC.

1. Front damage plate cutting size 2. New plate welding in place of damage plate by steel and low hydrogen electrode. 3. Front ribs new plate bending, shaping and welding size

1. Transmission guard damage portion straightening by gas heating. 2. Guard setting welding by steel electrode 3. Repairing of damage battery box straitening. 4. Battery box new sheet changing and welding.

Fabrication and erection of crusher cover and side cover size 3mx2m and 3mx1.5 m (12mm M.S. Plate ), under flow hopper using 12mm MS plate size 6000mm x 1200mm, its supporting by 65mmx65mmx 6mm angle total length 10 mtrs. In HMS Sec. at Kathara Ws.

Casting and machining of phosphor bronze impeller 07 Nos. and bearing bush 06 Nos for PV II Pumps(ii) Fabrication of middle chamber (including partition plate and guide vanes) for the 300GPM and 120/150 M MnP make pump at SBC Workshop under Sijua

Explosive Van Capacity 3 Te, FABRICATION & STATUTORY DOCUMENTAION of Explosive Van

1. Dismantling of complete hoist motor assly and stopper switch assly after cleaning from outside. 2. Hoist motor housing, welding, machining and facing etc. 3. Gear, welding, machining, polishing and straightening etc.

1. All four side of operator cabin rusted portion cutting and new sheet welding. 2. Glass frame denting, welding. 3. Operator seat and back rest repairing. 4. Broken safety glasses new changing.

1. Dismantling of complete hydraulic suspension piston and pin assly after cleaning from outside. 2. Piston welding, drilling original threading etc. 3. 2 nos. line boring, welding, grinding, machining and polishing etc.

1. Gouging of cracked bare tower. 2. V joint bead welding on cracked portion by steel electrode. - 3. Old plate cutting from grounded machine. 4. Both side plate welding on broken tower.

1- Steering Cylinder Complete Dismantling, Fitting. 2 Nos. 2- Steering Cylinder Bore Portion Scratching, Welding, Machining, Honing/Polish Proper Size. 3- Steering Cylinder Piston Scratch Welding, Repairing, Machining Proper Size. 2 Nos.

Please Refer ANNEXURE B in Tender Document

Dismounting of cutting edge from machine, welding of plate, fitment of cutting edge

1. Repairing of both rear transmission cover. 2. Plate cutting, shape making, welding.

For repairing of 30KVA, 550V Welding Machine of Tetulmari Colliery under Sijua Area

LETHER CLOTH BLACK, LETHER CLOTH WHITE, SR 998, ANABOND, WELDING ROD, M SEAL

Cabin frame denting welding and straightening both side. Safety glass fitting two nos.

Rough C.I casting for fabrication of misc. internal parts of pump at RR W/S, fabrication of C.I coupling for 2000 GPM pump motor set as well as DSM-6 set and for fabrication of other misc. job for repairing of pump at RR W/S, GRD

Fabrication/ Erection dismantling, 57 Screen and shifting to 58 Screen of Machine No. 48131-400-1845-3 sizzling screen type of USK-1.8M x 4.5M-LG Deck departure-75mm, grizzly type step deck. Weight of machine 4976 Kg of Raw Coal Section at KTW

For Repairing of 02 Nos. feed sprocket for DR-236 removal of seized thread of spindle sub in Drill DR-245 , fabrication of bushing centralizer as float for DR-236 and Removal of seized thread of broken Drill rod of Drill DR-262 , KATRAS AREA,

Fabrication of worn-out splines of driving shaft, driving wheel and Gun metal bush as float and repairing of worn-out take-up wheel (02 Nos.), driven half-coupling and slider jaw of Electric Rope Shovel (EKG) Sl. No. HMB-578 at ASBNC, Sijua Area

Repairing Fabrication of cutting edge and end bit, engine guard and its mountings, engine hood, operator cabin glass, LHS RHS railing, battery box, LHS RHS step ladder, wheel Dozer D20 also repair od 02 UJ assy of D355 for float at Ashok Opencast p

Fabrication and erection of 06 nos. lifter net frame and MS ring of outer side of wheel separator at 13 mtr level and repair of wheel separator by replacement of bottom sector (07 nos.), vertical sector (07 nos.), lifter net (07 nos.) with partial re

Repairing of sliding door glass frame, aluminum glass frame and new safety glass fitting, in IDM 30 drill Sl. No. 833 and RECP drill Sl. No. 817, fabrication of 02 set track chain guard in RECP drill Sl. No. 817 at Bansdeopur OCP, Sijua Area.

Fabrication and erection of A) Underflow chute full lining, magnetic separator drum frame, adjusting roller frame of unit no. 226 magnetic separator of Sec-I and B) Dilute media pump bypass unit no. 240 6 inch dia valve flange collector 400 m dia x 1

Repairing of idler pulley, 03 nos of tubes( exhaust manifold), 04 no bolt of exhaust manifold, repairing of EGR tube and EGR cooler, repairing of Hyd Tank guard RHS and LHS mudguard and LHS link (Radius rod), fabrication of rim assly of dumper D10352

For repairing of mast platform, adopter and guide shoe 02 nos. of Drill DR-196 , repairing of stem wrench and pipe tong weldment of Drill DR-245 and fabrication of new fork chuck 02 nos. of Drill DR-226 at AKWMOCP , KATRAS AREA, BCCL

Repairing, fabrication and erection of 471 screen overflow different pipe of OD 200 mm length 30 mtr with new and old serviceable pipe after dismantling of old damaged MS pipes in Fine coal Section and return water to scrap yard R/S at Kathara Washer

Dismantling of idle range of 10inch dia and 8inch dia MS pipes ranges from main patch and transporting the pipes to the attendance room premises for necessary repairing and fabrication of 10inch dia and 8inch dia MS bend taper pipe and reducer etc to

Work of 8 inch and 6 inch MS/GI pipeline work with dismantling, laying, pipe cutting, jointing, fabrication of bends etc work for pump shifting at coal face as well as 32 No. Sump including repairing of old damaged delivery pipelines under Dakra OCP

A) fabrication and commissioning of one (01) PVC drum pontoon for a 1000 GPM pump, along with B) repair of one (01) existing 72-drum pontoon used for a 2000 GPM pump, for deployment in the quarry sump to ensure efficient dewatering during the upcomin

(a) Fabrication , Machining and Fitting of 16inch Dia ist Gear Coupling for Motor to Gear Box of PIT No.-2 (men Winder)(B) Replacement of repaired/Serviceable 1 st and 3rd motion gear Box Pinion by hydraulic press machine of PIT No-2 at Kharkharee

Repairing of bucket eyes and pins along with adoption of tooth points in Tata Hitachi 650 excavator sl. no. 165 and repairing work towards fabrication of Float H Arm Assly. and 02 Nos. Side Links for Tata Hitachi excavator at Tapin North OCP HZB Area

Fabrication of leveling hydraulic jack pad (2 Nos.) and pin (4 nos.) eye hole repairing and repairing of L.H.S and R.H.S side guard, removal of broken roller bolt and new bolts fitting and new grease adaptor fitting of hydraulic jack of drill IDM30 D

Fabrication and erection of one vertical barrier of size 15 X 3 m made of GS sheet, angle and poles to take electrical safety during washing HEMM from OH line, conductor and installed transformer there at Tapin North O C P , under Hazaribagh Area.

Extracting of 02 nos. bush of boom, and new bush fitting and fabrication of engine stand, broken bolt removal, cutting and thread making of both side bucket and chain pad cutting, pin, bush removing and fitting and breezing of hyd pipe of CK300 Hydr

Dismantling, repairing and fabrication of Base Plate for two no. 500 GPM and two nos. 1000 GPM pump motor set and installation of same including associated pipeline work and providing and fixing of 6 inch dia sluice valve under IWSS, GM Unit, NK Area

02 times shifting of 1000gpm pump motor set domestic water supply pump in the upper side of the sump due to increasing of water level of albion OCP sump maintenance of the above pump and fabrication of tapper pipes and bends at Damoda Colliery

(A) (i). Repairing of float switch assembly twin entry (ii) Repairing of Radiator (iii) Repairing of Track drive gear box LH side (iv) Repairing fabrication of re-coil spring long shaft joint pin for running of 968 SDL machine at 4, 5 , 6 incline (B)

Fabrication of 02 Nos. of F shape of 10 inch Delivery, 2nos. of 10 inch suction short piece, 4 nos. of 10 inch Flange, 10 inch bend and associated work for installation of new 7.5m3/min pump in Main Pump Room 500MH Moonidih Project

Rep. of Hyd. Oil cooler platform, its brackets and frame, cooler tank, 02 nos. levelling jack pad and ball assly, HT Pin and locking arrangement and fabrication and installation of wet drilling of IDM-30 Drill Sl. No. 833 (DR-228) at ASBN OCP, Sijua

(A) Repairing of Air Circuit of Dumper Sl. No. 90030, (CIL No- 11866), and (B) Repairing/fabrication of L.H.S. and R.H.S dump body eye foundation box where hoist cylinder upper eye to be fixed of Dumper Sl. No- D - 90106, (CIL No- 12219, Model BH -

Dismantling of boom, stick assy from grounded shovel at Gidi-A, repairing of boom foundation eye housing with line bor-ing, fabrication of bushes in stick and boom along with dismantling and fitment of boom and stick in CK300E shovel sl.no E-164 of G

Repairing of damaged engine guards ,engine pulley ,LHS RHS railings ,fabrication of both side fork cover of WA600 Forklifter and Also Rep of 3 Nos stand for CAT C18 C32 Engine ,TIL transmission, and 02 Nos engine stand at W/s Ashok OCP.Refer NIT

Fabrication of accessories of pump i.e. bend, nipple and short piece of different sizes, etc. for installation of Kirloskar make 2000 GPM pump and Flowmore pump make 3000 GPM pump on the pontoon at HIRED Patch H and final starting of the pump of New