Fabrication Tenders in Jharkhand

Dismantling of Damaged Walkway Structures, Chequered Plates, MS Plates, Angles and Associated Structural Members, Fabrication, Refurbishment, Repair, Erection, Alignment and Strengthening of Conveyor Walkway Gantries of Clean Coal etc Sawang Washery

Fabrication,supplying and installation of Modular static kiosk of10 x 6 feet size with all electrical fittings at different stations of Dhanbad Division/East Central Railway as per the attached descri

Fabrication,supplying and installation of Modular static kiosk of 10 x 6 feet with all electrical fitting at different stations of Dhanbad Division /East Central Railway as per the attached descriptio

Custom Bid for Services - MODIFICATION OF PLATEFORM AT CC PUMP ELEVATION AND FABRICATION AND ERECTION OF PLATFORM AT ELEVATION 49500 FOR MAKING CUBICAL SITE OFFICE OF BTPS 1X500MW DVC BOKARO THERMAL

Custom Bid for Services - Fabrication of damage ISMB beam and chequered plate in Silo Section and repairing of top roller bracket and its related jobs in C18 C20 of Rajmahal CHP

1. Complete damage partition new plate changing 6mm 9 nos. partition. 2. New angle changing alignment and fitting. 3. Roof plate cutting welding alignment and fitting. 4. Complete repairing of water tanker- 9 Khana partition fitting.

Repairing and maintenance of differential system, break, jack system and bucket, front frame and lift arm pin bus welding, machining and grinding as per require size of L and T Loader 9020 at Kathara Washery

Following repairing is to be done in Dozer SD32W Sl.No.- 104841T-3279.(i)Repairing of Yoke shaft and yoke broken portion gauging, welding, opening and fitting both side (LHSand RHS). (ii)Repairing of Broken and damaged 02 nos. blade arm dismantling

For making of Bush type flange coupling 12in and 10inch diameter of cost steel metal for 4000 GPM, 1000 GPM pump of Nichitpur Colliery Under Sijua Area. . (b) For the Fabrication of CS Coupling 12inc dia) 6 Nos, for high GPM Centrifugal Pumps at SB

1.Worn out holes rebuilding and grinding as per pin size 2.New making of pin and fitting 3.Repairing welding of broken cylinder bracket both side welding by steel electrodes 4.Repairing of flange welding and fitting 5.Repairing and welding o

ENDOSCOPIC INSPECTION OF FURNACE & STOVE (Q3), CERAMIC WELDING MATERIAL ALUMINA BASED (Q3), CERAMIC WELDING MATERIAL SILICA BASED (Q3)

Manufacture/Fabrication, Inspection, Testing, Supply of Anchorage Accessories, Longitudinal AND Transverse Tie Rods Assembly, Temporary Tie Rods for Erection of Flash Plate, Brackets for Expansion Measurements and Springs for Anchorage (SM-101) as pe

Laying and welding of 340 mtrs 4 inch and 6 inch dia new pipeline for coal stock 39 and filling point at kundi fir the purpose of dust suppression under Magadh OCP, M-S Area

Dismantling, repairing/reconditioning and erection and welding at position of M.S. pipe line, flange, reducer and bends etc. in different position (as when required) of Section-Il in the Fine Coal Section of Kathara Washery

Repairing of Crowd clutch lining and hoist brake lining, Dipper handle eye (LHS and RHS) and M.G. set foundation cracked portion setting and welding of EKG 5A Shovel SI No. HMB-539 CIL No. 2591.

Cutting, dismantling, removing of damaged/deteriorated mother and liner plates cutting, positioning, welding of new mother and liner plates to discharge chute of rear conveyor of 1701 stacker I repairing , strengthening of grating, platform, railing,

Dismantling, repairing/reconditioning and erection and welding at position of MS pipe line, bends, reducer and flange etc. in different position (as when required) of Section-II of the Fine Coal Section of Kathara Washery

Dismantling of PTO Assembly from machine. Reconditioning of PTO body by grooving, cutting, welding and grinding. Reconditioning of input shaft flange and spline repairing.Sizing of bearing etc all work of CAT777D Dumper of Ashoka Piparwar

Clubbed work (1) Demounting, removing of deteriorated stringers with rollers, fitting and welding of new stringers with rollers to different 1400 mm conveyor belts under CHP-CPP, Piparwar Area,(2) cutting, dismantling, demounting, repairing, position

Following repairing is to be done in IDM30 Drill SI. No.201506853. Repairing of complete oil cooler tube welding, gauging, and cleaning with dismantling and mounting and repair work of all front and rear hyd.

Erection of 440 V OH Electric Line for providing proper lighting arrangement in the approach road leading to the Coal Stock, and three phase welding facility, in the same, w.r.t. Karo OCP, under BnK Area

Repairing of exhaust pipe by taking out broken bolt, air cleaner housing, battery box, alternator bracket, head light guard assly by cutting, welding, grinding and metal deposition in the dumper TH-14 at Ashoka OCP.

For repairing of 01 no. bend Drill rod and straightening and new thread of adopter making , welding and repairing of air cleaner housing elements 02 Nos. of Drill DR-245 at AKWMOCP, KATRAS AREA, BCCL

Repairing/rebuilding of worn out and broken lower portion of blade for fitting cutting edge and end bit and extra plate welding on blade of Dozer Model - BD-155, Sl. No.T-13592 of Jarangdih Colliery.

Repairing of water spray lines, water hanger, removal of rust scales from inside the tank by scraping, cutting, welding, grinding and metal deposition Repairing of radiator cover, operator cabin etc of Water Tanker of AOCP

Dismantling of turning joint and changing of complete new seal kit O ring. Broken boom foot eye by support welding pin rebuilding, machining and new bush pressing of ZX650H Tata Hitachi Exe - 186 of AKKOCP.

Repairing of operator dashboard, entire cabin body floor, door pillar, mudguard, footrest bumper, complete denting welding and rusted sheet changing and requires complete electrical harness, front spring leaf propeller shaft UJ cross with holder teet

(1) REAIRING AND MAINTENANCE OF 6.6 KV,400A,BIECCO MAKE,SL.NO.PB4/17866 AT GTC, AGKCC. (2) AIR COOL WELDING TRANSFOMER 550V/440 VOLT 450A SL.NO.AGKCC/6 PIT/01 AT AGKCC, KATRAS AREA. (3) SUPPLY, INSTALLATION

Renovation of wooden structure and damage steel cabin and providing of DGMS approved insulating mat and repairing of take-up axle and steel sleeve fitting and welding and roller side opening fitting of EKG 564.

3000 GPM PUMP LAKARKA RANGE 10INCH DIA PIPE LINE 210 MTR SHIFTING AT W.M.C,OCP WEST SUMP AND ALSO LEAKAGE REPAIRING BY WELDING TO PLACE OF OCP SUMP EAST SIDE OF WMC, AKWMC, KATRAS AREA

Repairing of damaged and worn-out boom foot eye and boom mounting eye both side turret structure by welding and line boring of ZX-650 Tata Hitachi backhoe Sl. No. DACG-0164, at Kathara Colliery.

Repairing of complete clutch system assly, brake unloader valve, treadle valve overhauling, repairing of rear both side spring leaf, removing and fitting and operator cabin door lock replacement fitting, both side mudguard cutting, welding, repairing

Repairing / rebuilding of worn out and broken lower portion of blade for fitting cutting edges and end bits and extra plate welding on blade of Dozer Model BD-155, Sl. No. 13592 of Jarangdih Colliery.

Repairing, Reconditioning and backfitment of raer shaft axle (bothside), shim replacement work, retainer housing, hub, ring, ring lock, differential arm by cutting, welding, grinding and machininh in Dumper CAT777D of TH-3 of Ashoka OCP.

Repairing and frame denting, welding, alignment setting and new safety glass front side fitting wiper dismantling and seat back rest fitting of shovel BE-1000-1 sl. no. 10222 at Nichitpur OCP of Sijua Area.

Repairing of Complete Clutch assy. like Clutch Plat Pressure Plat Kit Clutch Bearing Flywheel ring gear requires replacement fitting and Hydrolic Tipping valve overhauling repairing footrest and door denting welding repairing etc of miscellaneous acc

Differential trunion housing opening from S/off machine and inner drum damaged welding and machining (cast iron) differential opening and fitting and drive line opening and fitting of Pay Loader sl. No. P/L-284.

REPAIRING OF SPRING LEAF BELL, CRANK REPAIRNG AND WELDING AND REMOVAL SPRING BY CUTTING AND MAKING HOLE AND KIN PIN TAIL REPAIRING/ MACHINING JOB OF HYVA SL.NO.JH10AE 1608,JH10AE 1602, JH10AE 1609 AND BHW 8593

Cutting, welding of pipes and rearrangement , installation of 2000GPM pump at north east side of crew mines vi 8 inch range pipeline at crew mine for discharging of water in respect of akkocp bnk area

Repairing of both end crusher roll of Feeder Breaker No-2 along with cutting and welding of Picks with holders before and after repairing of crusher roll of Kessurgarh ABOCP Mine of Block-II Area.

Repairing of Hywa JH. 10AE 5464 like rear front spring leaf removing necessary recambering fitting and necessary hanger, shackle, pin, bush, bolt, washer requires replacement fitting and front bumper, door denting, outing, welding, repairing radiator

Repairing of Crowd clutch lining and hoist brake lining, Dipper handle eye (LHS and RHS) and M.G. set foundation cracked portion setting and welding of EKG 5A Shovel SI No. HMB-539 CIL No. 2591.

Repairing of old, damaged and serviceable steel tubular poles by cutting and welding of damaged part and joining for increasing its height for the use of different OHLs in mines under Purnadih OCP, NK Area.

Repairing of complete hydraulic brake booster , operator cabin denting , welding, repairing, water pump asssly, fan support, fan belt with tensioner, Diesel mobile filter kit, air filter/AC element are required replacement , fitting, fitting etc and

Repairing/rewinding of 28 KVA Welding Machine (Oil Cooled Machine) 02 phase , 350 Amps, 440 Volt, Sl. No. WNP at PCH and 2nd floor of main washing plant, deshaling plant and CCB of Sawang Washery.

Complete repairing, denting, welding and painting of house wall, ladder and railing pipe of house roof, ladder and crowd motor platform of EKG electrical Shovel SL.No. HMB 543/S383 of Kuya OCP, Bastacolla Area IX.

Repairing of bucket old plate cutting and operation size of plate 8X7inches-2 no, 7X12 inches-2 nos, 6X8 inches - 2nos. New plate fitting and cutting shape size welding of CKE300/159 of okaro ocp.

Welding and supply of 8 inch dia flange with 8 inch MS pipe for laying of new proposed pipe line from Crew Sump to outside mines premises for dewatering w.r.t Konar Exp Ocp,BnK Area

1.Repairing of diagonal frame cap both side and its bushing of BD 155 Dozer T-13642. 2.Repairing of damaged dump body with plate reinforcement, support welding of BH60M Dumper SL No D 60390.

Repairing and reconditioning of transmission input flange, engine guard, transmission guard by cutting, welding, grinding and its back fitment in dumper TH-2 under Asoka OCP. Repairing to be carried at site OR in situ.