Fabrication Works Tenders

M&L for MS props erecting for temporary supports to the structural members like beams, slabs etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work, complete all as specified and as directed by Engineer-in-Charge. Note- These supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements.

P & Fabrication steel rainforcement for RCC work including cutting, bending placing in position and binding complete including cost of binding wire in founcatino, etc. upto plinth level. cold twisted (IS:1786) bars. Up to floor three level (B-4/4.13.2)

Supply, fabrication installation and testing of site fabricated GSS metal ducts rectangular / circular duct as per site of size 1.0 mm thick / 18 gauge as per IS 277 (120 GSM both sides LFQ & confirming to class VIII) for GS sheets including necessary G.I hangers/ supports, volume control duct dampers, accessories vanes, 3 mm WPDM rubber gasket/duct tape etc complete all as specified and directed.

Design, fabrication, supplying and testing of dust, damp and vermin proof free floor standing sheet steel enclosed non-drawout indoor-IP 54 ,compartmentalised LT Main Panel, fabricated out of suitable sized angle iron and flats, base channel and covered with 2.0mm thick CRCA sheet, bending , punching to be done using CNC machines, duly powder coated complete with earth bus, aluminium bus bar, feeder labelling. 1) The feeder arrangement shall be as per SLD no: ICS/PMC/EL-SLD/02. 2) Switchgear and panel components shall be as per approved makes list. 3) Special instructions a) Switchgear shall have rotary handle for operation. b) There should be view (transparent ) window for Outgoing MCB of the Sub incomer (MCCB) feeder. c) Connectors/ busbars to be provided for outgoing cable connections. d) Size of cable alley should be adequete for housing the outgoing cables. e) Panel shall have top entry for cables. f) Panel shall be supplied with base frame. g) All live parts should have safety shrouding. h) Motor operated change over switch (MOS) shall have built in or external control circuit to sense Over Voltage,Under Voltage,Single phasing,loss of neutral, phase sequence etc. and indication showing status of load on MAINS/DG on the display unit of MOS. MOS shall have provision to set the parameters using external hand held unit. MOS shall have output control terminals for remote indication and remote start/ stop of DG during unhealthy power condition.

Supplying and fixing of Regular Office Table with Side Unit with following specification with 3 years warranty,, as per approved colour and design. Overall Dimention: 1500x600x750 mm Ht. Top made of pre laminated MDF board with pvc edge beading. Understucture also made up of pre laminated particle board with pvc edge beading. Top- Size :- 1500x600x25 MM thk. Pre Laminated MDF Board. Side edges covered by 2 mm thick PVC Edge beading by Through Feed Machine. Modesty- Modesty made up of 18 MM thk. Pre Laminated PMDF Board. Open edges covered by 2 mm thick PVC Edge beading by Through Feed Machine. Under Structure- Side Leg made with a Combination of 25 MM thk. Pre Laminated MDF Board with Aluminium section of size 60X40 with grooving. Leg/Side Base & Top plate with profile cut made of M.S. plate 44 mm width & 4 mm thk with knock down fitting arrangement. Cable duct made up of 0.8 mm CRCA Sheet. Provision of Cable manager as per L.H. or R.H. side requirement. Open edges of MDF board covered by 2 mm thick PVC Edge beading by Through Feed Machine. SDU with Drawer- Size: Height:750mm,Width:900mm,Depth:450mm. Body part made-up of prime quality cold rolled close annealed Sheet Use only MIG/TIG & Spot welding for fabrication. Top made of 18mm thick Pre-laminated MDF Board. Side Edges covered with PVC edge band on edge bending machine. Provision of drawer below table top with telescopic channel. Superior Quality make lock. PVC handles. Doors in cold rolled close annealed M.S. Sheet. Doors are Top hung slide on roller bearing. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. Cap & Levellers- Flat type leveller has been provided at bottom for mentaining level. It also preventing scratches on floor & Product as well. Construction- The product comes in knock-down conditional for ease of transportation. Finish- No sharp edges in the prodect. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface.

VRCC M-20 grade nominal mix (cement :fine aggreegate: coarse aggregate) corresponding to table 9 of IS456 using 20mm size graded machine crushed hard granite metal (coarse aggreegate)from approved Quarry including cost and conveyancej of all materials like cement,fine aggregate(sand)coarse aggregate, water etc, to site and includng centering and shuttering etc, but excluding seigniorage charges,sales and other taxes on all materials including all operational incidental and labour charges such as machine mixing , laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work,