Loading…
Loading…
1,416 results • Best match
Civil works
SOLAR STREET LIGHTING SYSTEM: * 30Watt Solar Semi Integrated street light (LED Make:Osram/Philips) * 24AH 12.8V LiFEPO4 Battery with mppt Charge Controller. * 75 Watt solar PV Module. * 1.Supply of 5m height 5 inch dia GI (Average dia tappered from bottom to top) tubular pole and at the bottom one base plate of size 30 x 30 x 5 mm having a through hole of size 14 mm dia at the centre of the ase plate with recuired nut and bolt with pole cap Pole with Light arm and PV Structure. 2.Painting of tubular pole with arms with ant coat of red oxide primer and two coats of aluminium paint and bottom one meter with black paint with supply of paints and labour. 3.Labour charges towards installation of 5 mtr height steel tubular pole including concreting of pole base and couping with supply of concreting materials as per following specification. Planting depth of,1.5 mtr pole pit size 1.2 x 1.2 x 1.8 m concreting- 1:4:8 with 4 cm HG metal size and couping of standard size into 40 cm X 40 cm X 50 cm with cement concreting 1:2:4 uaing 20 mm BHCBG chips. This includes the cost of all concreting materials, labour and hire charges of all T&P materials. The pole is to be installed in proper alignment as per the direction of Engineer in charge, and enclosed drawing and specification. Transportation & Installation charge with concrete work.Complete 5 years warranty.
REPAIR REPLACEMENT OF INTERNAL UNSERVICEABLE POINT WIRING FITTING FIXTURE AND CONNECTED ACCESSORIES WORK IN TARAPORE ENCLAVE, KHETRAPAL ENCLAVE AND ABDUL HAMID UNDER AGE EM IV OF GE(S) BATHINDA AT BATHINDA MIL STN
S&F in replacement thermostat ISI marked stem type 240 Volts, AC supply temp range at least 30 to 75 degree C for geyser/solar water heater system complete all as specified and directed by Engineer-in-Charge.
REPAIR/ REPLACEMENT OF EARTHING , LT PANEL , MCCBs, BUS BAR, CHANGEOVER, PAINTING OF POLE AND OTHER E/M MISC WORK AT BB CANTT, SRINAGAR
Supply & fix in repair of heat collector glass size 80"X40" suitable for solar water heater of capacity 500/1000 LPD as per existing type and sizes, complete all as specified and directed
Refer to BOQ
Supplying, installation, Testing & Commissioning of the integrated type solar PV lighting system on the existing pole structure, comprising of 20 watt, 6V Mono Passivated Emitter and Rear Contact (PERC) Solar Panel (minimum efficiency 21%), Pulse with modulation (PWM)/Maximum Power point tracking (MPPT) Charge Controller in the box with a sleek appearance and a sturdy structure, is weather-proof, and is simple to install, With Lithium- Iron Phosphate Battery (LiFePO4),charging time 6-8 hours, Battery backup time 12 hours (minimum), LED fixture 20 watt, Input voltage: 12V DC, Operating temp range -5 °C to 50 °C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%, IP-66,IK-08, CRI >70 , under voltage and over voltage protection, Electro Magnetic Interference (EMI) Electro Magnetic Compatibility (EMC) As per CISPR 15, lenses for beam angle as per Illuminating Engineering Society of North America (IESNA) type I/II/III as per the width of the road and the project requirement, Correlated Colour Temperature (CCT) 5700°K / (As per American National Standard Institute (ANSI Bin)), life time (LED,Driver & electrical circuitry) of 50K hours lamp buring hours till the 70 % of initial Lumen maintained as per LM80 extrapolation IES TM-21-11 report, automatic swich on/off, Alliuminium or Acrylonitrile Butadiene Styrene (ABS body), can be installed on a pole or wall. System lumen efficacy >120 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. All as per pre approved by Engineer in-charge complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required, complete with mounting structure for the battery and accessories suitable for withstand wind storm speed as per the site location. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).
Carrying out Zone works for period ending 30.06.2027 on Zone No-6 Mech. Workshop including workshop administrative building and store depot Izzatnagar.
Supplying & installation of wind driven turbine Each ventilator with FRM base to match profile of aluminum galvanized corrugated (GC) roofing sheets of SVS make or similar of throat/elbow diameter 24'' to be fixed on the roof of the sheds. Installation shall be done in such manner that the roof remains watertight and leak proof.
Development of all major roads (strengthening, widening, beautification and horticulture work) from PWD rest house to old bus stand including all cross roads form NDRI boundary wall to railway road.(Recall)
[34.36]Solar RPM/ Stud Providing and installation of solar cat eye produced from an engineered polymer selected for superior impact resistance and weather-ability. The top of the solar stud should be transparent for solar charging and light output in active mode. The base of the body shall be yellow or neutral white as approved by Engineer In-charge. The marker shall incorporate a solar panel (comprising of solar cells) for converting solar energy into electricity, a storage device for storing the energy, LEDs for illumination and a design for providing 360 degree smooth illumination. The Solar stud shall be round in shape for providing illumination in all directions. The solar stud shall also have high reflective polycarbonate/ methyl methecrylate lenses for conspicuity in passive mode and dual shanks for improved road presence. The solar studs are intended for application directly onto pavement surfaces and shall be applied with epoxy resin adhesives designed for use with raised pavement markers and as supplied by the marker manufacturer separately. The solar cat eye shall be of height: 65 ± 2 mm & Maximum Diameter: 136 ± 5 mm. The body of the solar cat eye shall be resistant to dust and water ingress as per IP 65 standards. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. [Through Rate]