Loading
Loading…
Loading…
415 results • Best match
SUPPLY AND INTEGRATION OF MOTION AND VIBRATION SYSTEM FOR LEVEL D CERTIFIABLE HELICOPTER FMS
4.2. Performance requirements of Motion control system a) Effective Stroke : equal to or More than 1400 mm. b) Payload : equal to or More than 13,000 kg. c) Moment of inertia in X axis ( Ixx) with pay load : equal to or more than 41000 kg /m2 d) Moment of inertia in Y axis ( Iyy) with pay load : equal to or more than 41000 kg /m2 e) Moment of inertia in Z axis ( Izz) with pay load : equal to or more than 41000 kg /m2 f) Centre of Gravity of height above motion platform centroid: equal to or more than 1790 mm g) Motion Envelope requirements The proposed motion system shall meet the following minimum Motion Envelope requirements with single degree of freedom.
Supply & Apply of M.S. Grills of various locations of Boiler, APH , ESP & Coal Mill Platform area for Unit No. 1, 2 & 3 of BMD I & Unit No. 4, 5 & 6 of BMD II at WTPS .
Department/Electrical Safety Officer/Dy.Safety Officer/ Safety Officer/Factory Manager.
DESIGN AND DEVELOPMENT OF UNFEATHERING PUMP FOR DO-228 AIRCRAFT
2.2 Bid received with technical bid and price bid in open condition inside one envelope will be rejected.
Construction of 220KV D/C Transmission Line from PMTL, Chandauti to IMC ,Dobhi (RL - 22.9 KM ) with ACSR Zebra Conductor along with Construction of 02 nos. 220KV Line Bays at Chandauti PMTL Substation on Turnkey basis.
8 Nominal Peak Envelope Power (with Distortion and Inter modulation Products 80 dB down)
SUPPLY OF AERIAL FIRE FIGHTING EQUIPMENT
Scope of Supply, Space Envelope and Weight Budget: Note : The total empty weight of the AFFE shall be approximately 232 Kg. Vendor shall indicate the actual weight of the AFFE and supply the same with minimum possible weight.
RUGGEDIZED AMLCD HEAD ASSEMBLY
4.2 Display Requirements [0608RAHA_004] 0608RAHA shall have an active area of 6” x 8” (152.4x203.2 mm) and pixel size shall not be more than 0.198 x 0.198 (mm). [0608RAHA_005] 0608RAHA shall have 02 no’s of Automatic Brightness Control (ABC) of the display using Illumination sensors located on bezel. The Control law of the automatic brightness control shall be subject to evaluation and modification (if required) during integration testing. Manual brightness control shall be provided, which may override the software set automatic brightness. Position of ABC sensor shall be defined during D&D phase by considering the installation, ambient light effect in cockpit and by considering the interchangeability aspects [0608RAHA_006] The display resolution of 0608RAHA shall not be less than 768x1024 (minimum) RGB pixels or better. [0608RAHA_007] Viewing Angle: The display shall be clearly readable and the characteristics & performance of display shall be guaranteed for following viewing angles measured with respect to center of display a) Horizontal: ± 60° or better b) Vertical: -35° to +55° or better. [0608RAHA_008] Brightness Uniformity: For a white pattern, the brightness shall not vary from the average by more than 25 % over the display surface for any brightness level for the entire viewing envelope. [0608RAHA_009] Touchscreen: 0608RAHA shall have a touchscreen capability. Type of touchscreen technology shall be Resistive type for initial Two Numbers. After assessment of touchscreen performance with respect to Universal Aviation Gloves, vendor may need to change the touch screen type from Resistive type to Infra-red Type from stage-2 as per 0608RAHA_070. 0608RAHA shall be compatible for operation of Touchscreen with and without Gloves. During submission of proposal, Vendor should cater in the proposal for the requirement of Resistive type or Infra-red type without any additional cost during later stages of delivery. [0608RAHA_010] a). Touchscreen shall be multi-touch (up to 4 points) and controlled through software to enable/disable Touch/ No Touch mode. b). The Touch Mode enable / disable shall be indicated in BIT. c). The reported touch screen location should be accurate within 2 sq. mm ± 1 sq.mm. Any Invalid touch information shall be provided for recording in data Log. d). 0608RAHA shall be able to differentiate between single and multiple touch/press inputs. e). 0608RAHA shall provide positive feedback to pilot for confirmation of an input of touch.
