Loading
Loading…
Loading…
Tender Value
₹2.7 Cr
EMD Value
₹2.9 L
Closing Date
16 Dec 2025, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
SOU WORKS
18 conditions · 4 needing a document upload
Financial Eligibility Criteria: as per Clause 10.2 of Part-I of IRSGCC-2022 and as per Railway Board Advance correction slip No.1 dated 14-07-2022 The tenderer must have minimum average annual contractual turnover of V/N or "V" whichever is less: where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-F (AnnexureVIB of GCC), along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Account duly supported by Audit balance Sheet .
Financial Eligibility Criteria: As per Clause 10.2 of IRSGCC-2022 (As per Advanced Correction slip No,1 dated. 14.07.2022 to GCC-2022) and the same is mentioned in Para No.10.2 page no. 15 of this tender document. Tenderer should attach Selfattested/ Digitally signed copy of Certificate showing minimum average annual contractual turnover as per Annexure VIB of IRSGCC-2022 (As per Advanced Correction slip No,1 dated. 14.07.2022 to GCC-2022) in Annexure - "F"Page-32 of Master Document - 1 attached to the tender
Similar Nature of work : Any Civil Engineering works excluding zonal works
Technical Eligibility Criteria: As per Clause 10.1 of Part-I of IRSGCC-2022 (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender
(b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed orsubstantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2) In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the 1.1.1 Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarized, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfillment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be sub-let, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing.
Note for Item 10.1 of IRSGCC-2022: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organization, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work 1.1.2 experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Instructions to Tenderers and Conditions of Tender: Tenders are refer Annexure-I, Tender Form (Second Sheet) Part-I of IRSGCC-2022 is mentioned from page No. 11 - 26 of Master Document -1 attached to the tender
16 conditions · 6 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tender value is including escalation of (- )10% (minus ten percent ) on CPWD DSR rates. Tenderer should note this before quoting the rates
The original Bank Guarantee (in lieu of Bid Security) should be delivered in person to the official nominated (i.e. OS/Tenders/Engg) / BZA Division) as indicated in the tender document before closing date for submission of bids (i.e. excluding the last date of submission of Bids).
All the instructions furnished in the Technical Compliance / Commercial Compliance / Custom / Undertakings / General Instructions are only indicative and not exhaustive. The tenderer shall read the GCC / Tender documents for complete details.
The tenderer shall thoroughly go through the entire tender document and strictly adhere to the instruction and directions given therein
SW I: OGL -Improvements to waiting halls and waiting Rooms including toilets, VIP lounge, Booking Office, Parcel office, Platform surface at OGL(PF 4&5)and other passenger related amenities on PF 1 Ongole ADEN/OGL Sub Division of Sr.DEN/SOUTH/BZA jurisdiction. SW II: SKM - Improvements to Platform surface on PF3 including water supply arrangements, stainless steel water booths and stainless steel seating benches on Island platform.
E-23-south-BZA-2025~SCR
E-23-south-BZA-2025
Open
Works - General
9 Months
Krishna, Andhra Pradesh
₹0
₹2.9 L
16 Dec 2025
24 Nov 2025
2 Dec 2025
129 items across 4 schedules · ₹2,21,83,833.64 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil. | cum | 90 | 260.3 | 23,427 |
| 2 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 100 | 10,011.35 | 10,01,135 |
| 3 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum | 47.25 | 7,370.65 | 3,48,263.21 |
| 4 | Cement mortar 1:6 (1 cement : 6 Coarse sand) | cum | 99 | 8,752.55 | 8,66,502.45 |
| 5 | Area of slab over 0.50 sqm | Sqm | 275 | 5,136.3 | 14,12,482.5 |
| 6 | Granite Stone of approved shade | Sqm | 5.76 | 4,051.85 | 23,338.66 |
| 7 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 40.32 | 3,167.95 | 1,27,731.74 |
| 8 | 150x10 mm | Each | 32 | 287.25 | 9,192 |
| 9 | 300x16x5 mm | Each | 16 | 322.2 | 5,155.2 |
| 10 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. | Each | 13 | 1,124.85 | 14,623.05 |
| 11 | 125 mm | Each | 16 | 231.05 | 3,696.8 |
| 12 | 75 mm | Each | 16 | 176.4 | 2,822.4 |
| 13 | Triple strip vertical type | Each | 15 | 52.5 | 787.5 |
| 14 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. | Metre | 96 | 570.95 | 54,811.2 |
| 15 | 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge. | Sqm | 34.65 | 4,488.95 | 1,55,542.12 |
| 16 | Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 18 mm thick confirming to IS:14587 | Sqm | 42 | 1,248 | 52,416 |
| 17 | Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 25 mm thick confirming to IS:14587 | Sqm | 42 | 1,874.7 | 78,737.4 |
| 18 | 200 mm | Each | 31.2 | 186.65 | 5,823.48 |
| 19 | 5.5 mm thick glass panes | Sqm | 25.2 | 1,390.15 | 35,031.78 |
| 20 | Size of Tile 600 x 1200 mm | Sqm | 460.65 | 1,798.8 | 8,28,617.22 |
| 21 | Size of Tile 600x600 mm | Sqm | 1100 | 1,623.05 | 17,85,355 |
| 22 | Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. | Sqm | 180 | 3,186.7 | 5,73,606 |
| 23 | Flat surfaces | Sqm | 240 | 1,718.95 | 4,12,548 |
| 24 | 110 mm diameter | Metre | 300 | 377.4 | 1,13,220 |
| 25 | 110 mm bend | Each | 50 | 150.35 | 7,517.5 |
| 26 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 542.5 | 738.65 | 4,00,717.63 |
| 27 | 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. | Sqm | 838.15 | 2,215.15 | 18,56,627.97 |
| 28 | 1:4 (1 cement: 4 fine sand) | Sqm | 750 | 347.05 | 2,60,287.5 |
| 29 | 1:6 (1 cement: 6 fine sand) | Sqm | 300 | 333.35 | 1,00,005 |
| 30 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 1407.11 | 262.7 | 3,69,647.8 |
| 31 | New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm | Sqm | 444.19 | 223.6 | 99,320.88 |
| 32 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture | Sqm | 63 | 176.25 | 11,103.75 |
| 33 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture | Sqm | 78 | 170.7 | 13,314.6 |
| 34 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Sqm | 195 | 156.05 | 30,429.75 |
| 35 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 19.5 | 2,434.25 | 47,467.88 |
| 36 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | cum | 18 | 3,551.25 | 63,922.5 |
| 37 | In cement mortar | cum | 120 | 2,060.2 | 2,47,224 |
| 38 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | cum | 165 | 263.95 | 43,551.75 |
| 39 | Providing and laying C.C. pavement of mix M- 25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). | cum | 100 | 9,823.8 | 9,82,380 |
| 40 | With granite stone of colour black, cherry/ruby red of area less than 0.50 sqm. | Sqm | 480 | 4,950.9 | 23,76,432 |
| 41 | Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in- Charge. | Sqm | 97.5 | 2,017.6 | 1,96,716 |
| 42 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 4 | 6,767.4 | 27,069.6 |
| 43 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 9 | 6,515.55 | 58,639.95 |
| 44 | One urinal basin with 5 litre white P.V.C. automatic flushing cistern | Each | 4 | 6,258.75 | 25,035 |
| 45 | White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps | Each | 15 | 2,301.75 | 34,526.25 |
| 46 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. | Each | 25 | 349.15 | 8,728.75 |
| 47 | 32 mm dia | Each | 10 | 103.9 | 1,039 |
| 48 | Circular shape 450 mm dia | Each | 16 | 1,479.05 | 23,664.8 |
| 49 | C.P. brass | Each | 4 | 803.7 | 3,214.8 |
| 50 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. | Each | 26 | 168.35 | 4,377.1 |
| 51 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. | Each | 15 | 231.95 | 3,479.25 |
| 52 | 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms | Each | 12 | 673.4 | 8,080.8 |
| 53 | 50 mm nominal dia Pipes | Metre | 500 | 934.15 | 4,67,075 |
| 54 | 20 mm nominal dia Pipes | Metre | 400 | 537.6 | 2,15,040 |
| 55 | 50 mm nominal bore | Each | 5 | 1,026.65 | 5,133.25 |
| 56 | Vertical | Each | 4 | 1,445.15 | 5,780.6 |
| 57 | Vertical | Each | 2 | 3,855.4 | 7,710.8 |
| 58 | 15 mm nominal bore | Each | 30 | 85 | 2,550 |
| 59 | 15 mm nominal bore | Each | 15 | 97.75 | 1,466.25 |
| 60 | 150 mm diameter | Each | 10 | 222.35 | 2,223.5 |
| 61 | Class II | Each | 14 | 4,985.85 | 69,801.9 |
| 62 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per Litre | 10000 | 11 | 1,10,000 |
| 63 | 15 mm nominal bore | Each | 20 | 506.8 | 10,136 |
| 64 | 15 mm nominal bore | Each | 8 | 820.7 | 6,565.6 |
| 65 | 15 mm nominal bore | Each | 10 | 798.95 | 7,989.5 |
| 66 | 15 mm nominal bore | Each | 8 | 670.45 | 5,363.6 |
| 67 | 15 mm nominal bore, 90 mm long, weighing not less than 93 gms | Each | 20 | 196.75 | 3,935 |
| 68 | 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms | Each | 20 | 224.1 | 4,482 |
| 69 | 50 mm dia | Each | 6 | 5,748.8 | 34,492.8 |
| 70 | 80 mm dia | Each | 4 | 6,993.6 | 27,974.4 |
| 71 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. | Each | 12 | 111.45 | 1,337.4 |
| Schedule total | ₹1,62,28,445.12 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Tenderschedule.pdf
ATTACHMENT
buildingconditions11.pdf
ATTACHMENT
earthworkconditions4.pdf
ATTACHMENT
Generalconditionsrevised21.pdf
ATTACHMENT
RevisedBrandsandmakesapprovedlist2025.pdf
ATTACHMENT
SAFETYTrackConditions11.pdf
ATTACHMENT
MasterDocument01-Oct-25.pdf
ATTACHMENT
MasterDocument2.pdf
ATTACHMENT
DESIGNMIXHQrsLETTERONSPECIALCONDITIONSFORDESIGNMIX2123-03-202221.pdf
ATTACHMENT
SpecialConditionsmodified1.pdf
ATTACHMENT
Specificationofconcrete12.pdf
ATTACHMENT
SPECIFICATIONSGALVALUMESHEETS16.pdf
ATTACHMENT
Steelspecialconditions1.pdf
ATTACHMENT
TrDSpl.Conditions12.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .