Providing paintings to central divider on Nunna Road from Nandamuri Nagar Junction to Kandrika Junction & Nandamuri Nagar Road from Saibaba Temple to IRR Road and Junction improvements of Thermoplastic Zebra lines with reflective studs of AE-7 Section in Works Division-II Area

Labour engaged for removing of damaged plaster surface, removing of stickers, cleaning with chemicals and all labour charges etc., complete and as directed by the departmental authorities.

Plastering in CM (1:4) 12mm thick including cost and conveyance of all materials and labour charges for mixing of mortor, watering, curing etc., complete.

Painting, priming coat on new plastered surface to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and all operational, incidental labour charges etc., complete for finished item of work as per SS.

Painting with Solvent Based Kerb Guideline Synthetic enamel paint of Berger / any ISI make (SB RM Paint) in a single pack, alkyd based for two coats - on any new / old plastered surface to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and all operational, incidental labour charges etc., complete for finished item of work as per SS including enamel based prime coat as per SS.

Supplying of hot applied thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with relectorising glass beads on bituminous surface at 250gms per Sqm area, thickness of 2.5mm is exclusive of surface applied glass bead as per IRC:35, the material should be of BERGER company / BERGER equivalent and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department) b) Luminance factor of the material should be in the range of 80-85% at 45degree centigrade as per AASTHOM 249 c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS 3262, Part-1 1989 and should pass at the range of '0' degree centigrade to '-10' degree centigrade d) Adhesion: Strong e) Softening point: 102 degree centigrade f) Dried film finish: Smooth and uniform g) Night vision: High as directed by the Engineer-in-Charges and conforming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-1997.

Supply and fixing of Molded Shanks raised pavement markers made of polycarbonate and ABS molded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000Kg tested in accordance to ASTM D 4280 type H and complying to specifications of Category A of MORTH circular no RW / NH-33023/ 10-97-Do III, Dt.11.06.1997. The height, width and length shall not exceed 50mm, 100mm and 100mm with minimum reflective area of 13 Sqm on each side and the slope to the base shall be 35+/- 5 degree. The strength of detachment of the integrated cylindrical shaks, (of diameter not less than 19 +/- 2mm and height not less than 30 +/- 2mm) from the body is to be a minimum value of 700Kgs. Fixing will be by drilling holes on the road for the twin shanks to go inside without nails and using epoxy resin based adhesive as per manufacturers recommendation etc., complete and as directed by the Engineer-in-Charge.