Loading…
Loading…
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹7.9 Cr
EMD Value
₹15.8 L
Closing Date
27 Oct 2026, 3:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
BUILDINGS
18 conditions · 4 needing a document upload
Financial Eligibility Criteria: as per Clause 10.2 of Part-I of IRSGCC-2022 and as per Railway Board Advance correction slip No.1 dated 14-07-2022 The tenderer must have minimum average annual contractual turnover of V/N or "V" whichever is less: where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-F (Annexure-VIB of GCC), along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Financial Eligibility Criteria: As per Clause 10.2 of IRSGCC-2022 (As per Advanced Correction slip No,1 dated. 14.07.2022 to GCC-2022) and the same is mentioned in Para No.10.2 page no. 15 of this tender document. Tenderer should attach Self-attested/ Digitally signed copy of Certificate showing minimum average annual contractual turnover as per Annexure VIB of IRSGCC-2022 (As per Advanced Correction slip No,1 dated. 14.07.2022 to GCC-2022) in Annexure - "F" Page-32 of Master Document -1 attached to the tender
Similar Nature of work : "C.II - Any Civil Engineering Work (excluding Track works / Zonal works)"
Technical Eligibility Criteria: as per Clause 10.1 of Part-I of IRSGCC-2022 (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender
(b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfilment of technical eligibility criteria for different components. (b)(2) In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the 1.1.1 Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must ulfil technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing
Note for Item 10.1 of IRSGCC-2022: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organization, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work 1.1.2 experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Instructions to Tenderers and Conditions of Tender: Tenders are refer Annexure-I, Tender Form (Second Sheet) Part-I of IRSGCC-2022 is mentioned from page No. 11 - 26 of Master Document -1 attached to the tender.
16 conditions · 5 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tender value is including escalation of (-)15% (minus Fifteen percent ) on CPWD DSR rates. Tenderer should note this before quoting the rates.
The original Bank Guarantee (in lieu of Bid Security) should be delivered in person on any working day to the official nominated (i.e., OS/Tenders/Engg)/BZA Division) as indicated in the tender document before closing date for submission of bids (i.e. excluding the last date of submission of Bids).
All the instructions furnished in the Technical Compliance / Commercial Compliance / Custom / Undertakings / General Instructions are only indicative and not exhaustive. The tenderer shall read the GCC / Tender documents for complete details.
The tenderer shall thoroughly go through the entire tender document and strictly adhere to the instruction and directions given therein.
PAP : Provision of COP Shelters on PF-No.1 and Proposed Improvements to PF surface on PF 1, Station Facade and Circulating Area at Pithapuram Station in SSE/W/SLO section under ADEN/SLO sub-division under ABSS.(Umbrella Work Project ID : 33.03.53.26.3.00.001 of 2026-27) - SW-I: Proposed Improvements to PF Surface on PF 1, Station Facade and Circulating Area at Pithapuram Station.
E-26-North-BZA-2026~SCOR
E-26-North-BZA-2026
Open
Works - General
12 Months
Krishna, Andhra Pradesh
₹0
₹15.8 L
30 Sept 2026
30 Sept 2026
13 Oct 2026
48 items across 4 schedules · ₹9,23,22,800.22 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 230 | 177.5 | 40,825 |
| 2 | Depth exceeding 1.5 m but not exceeding 3 m | Sqm | 120 | 81.6 | 9,792 |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 28.02 | 2,123.75 | 59,507.48 |
| 4 | Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge. | cum | 481.6 | 308.2 | 1,48,429.12 |
| 5 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 220 | 7,878.5 | 17,33,270 |
| 6 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 1247.17 | 7,178.75 | 89,53,121.64 |
| 7 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 180 | 392.15 | 70,587 |
| 8 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 729.6 | 736.4 | 5,37,277.44 |
| 9 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 396.96 | 961.3 | 3,81,597.65 |
| 10 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 77.1 | 10,585.9 | 8,16,172.89 |
| 11 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 82.35 | 9,655.7 | 7,95,146.9 |
| 12 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 1149.11 | 10,011.35 | 1,15,04,142.4 |
| 13 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 311.91 | 7,132.25 | 22,24,620.1 |
| 14 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 863.04 | 772.4 | 6,66,612.1 |
| 15 | Dark shade pigment using ordinary cement | Sqm | 2080 | 1,119.5 | 23,28,560 |
| 16 | Size of Tile 600 x 1200 mm | Sqm | 2550 | 1,577.15 | 40,21,732.5 |
| 17 | Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. | Sqm | 2255 | 3,186.7 | 71,86,008.5 |
| 18 | 110 mm diameter | Metre | 251 | 377.4 | 94,727.4 |
| 19 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 100 | 738.65 | 73,865 |
| 20 | 1:6 (1 cement: 6 fine sand) | Sqm | 2303.92 | 333.35 | 7,68,011.73 |
| 21 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 2084 | 262.7 | 5,47,466.8 |
| 22 | Two or more coats on new work | Sqm | 100 | 155.9 | 15,590 |
| 23 | Two coats | Sqm | 875 | 142.8 | 1,24,950 |
| 24 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 63 | 2,434.25 | 1,53,357.75 |
| 25 | Cement concrete prepared with batch mixing machine | cum | 576 | 10,529.35 | 60,64,905.6 |
| 26 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). | cum | 420 | 9,823.8 | 41,25,996 |
| 27 | 25 mm nominal dia Pipes | Metre | 80 | 355.4 | 28,432 |
| 28 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per Litre | 15000 | 11 | 1,65,000 |
| 29 | 15 mm nominal bore | Each | 20 | 506.8 | 10,136 |
| 30 | 15 mm nominal bore | Each | 25 | 820.7 | 20,517.5 |
| 31 | 300 mm dia piles | Metre | 81 | 3,065.6 | 2,48,313.6 |
| 32 | Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6 mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthened clear float glass 6 mm thick, spacer tube 12 mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor.(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, + 12 mm Air gap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. | Sqm | 18 | 3,718.7 | 66,936.6 |
| Schedule total | ₹5,39,85,608.7 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
MasterDocument01dtd11-09-2026..pdf
ATTACHMENT
MasterDocument02dtd11-09-2026..pdf
ATTACHMENT
1.Schedule1..pdf
ATTACHMENT
2.Generalconditionsrevised.pdf
ATTACHMENT
3.buildingconditions.pdf
ATTACHMENT
4.Specificationofconcrete.pdf
ATTACHMENT
Design mix Conditions
ATTACHMENT
8.SPECIFICATIONSGALVALUMESHEETS.pdf
ATTACHMENT
9.TrDSpl.Conditions..pdf
ATTACHMENT
10.SAFETYTrackConditions.pdf
ATTACHMENT
11.Earthworkconditions.pdf
ATTACHMENT
5.RevisedApprovedlistofBrandsandMakes2026withallenclosures26-02-26.pdf
ATTACHMENT
6.DESIGNMIXHQrsLETTERONSPECIALCONDITIONSFORDESIGNMIX2123-03-2022.pdf
ATTACHMENT
12.SpecialConditionsfordrgsmodified.pdf
ATTACHMENT
SimilarNatureofWorks02-12-25.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .