Fabrication Tenders in Jharkhand

1. Welding, machining and grinding of gear shift linkages. 2. Hole making in lever for pin fitting.

Mechanical Repairing ,Cutting,Welding and Maintenance of 60 MT Road WB installed at Potanga under Urimari OCP.

1. Transmission guard damage portion straightening by gas heating. 2. Transmission guard setting welding by steel electrode.

FLOUROSCENT TAPE 2 INCH, FLASHLIGHT, APRON LEATHER WELDING, ELECTRIC RUBBER HAND GLOVES, EARTH LEAKAGE RELAY WITH CBT

Repair n Fabrication of 04 sets of cutting edge for BG825 Grader of Ashok OCP

For fabrication of conveyor snub drum for FB-1 at FB, SBC under Sijua Area

Dismantling of exhaust silencer,fixing of circular shape plate,fabrication of foundation,mounting of exhaust

Acetylene Pressure Regulator - as per IS 6901 (Q3), oxygen gas regulators (Q3), Electrode Holder - as per IS 2641 (Q3), Welder Gloves or Gauntlets- as per IS: 2573 (Q3), Blow Pipe For Welding And Cutting-IS 7653 (Q3), Rubber Welding Hoses-IS 447 ... (Q3), Welding apron ...

Please Refer ANNEXURE B in Tender Document

SOLID MIG/MAG WELDING FILLER WIRE, CLASS VI SIZE 1.2 MM (SPEC.NO.IRS M- 46/13 WITH AMENDMENT NO.1 GRADE ER 308 L AS PER AWS:A5.9-10)IN SPOOL OF 12.5 KGS/ROLL specn: (SPEC.NO.IRS M-46/13 WITH AMENDMENT NO.1 GRADE ER 308 L AS PER AWS:A5.9-10)IN SPOOL OF 12.5 KGS/ROLL

Dismantling of trailing cable repairing mounting bracket fitment of mounting bracket

1. Replacement of capacitor bank assy. 2. Replacement of Current regulator 3. Replacement of brass connection stud with insulator nut washer etc.

1.Replacement of capacitor bank 1 set 2.Replacement of current regulator 01 no 3.Replacement of connection stud 03 set 4.Replacement of line filter assembly 01 no 5.Replacement of current selector switch 01 no. 6.Replacement of cable and card

Repairing of broken bracket, pin and eye holes of tilt cylinder of BD-355 Dozer Sl. No. T-11723, Repairing / fabrication pf 04 Nos. tilt cover of D-355 Dozer Sl. No. T-11722 and T-11890 and Repairing of R.H. and L.H. arm end and U portion of BD-355 D

WRD/IMD/RANCHI/07/2025-26 Renovation of U/S and H/R Gate at Head Works site and C/R gate at Ch. 3.2 K.M and Fabrication, Fitting and Fixing of H/R gate at Ch. 7.7 K.M of Main Canal and 03 Years Repair and maintenance of Vijay Weir Scheme.

1. Damage blade arm broken plate cutting inside lower and upper size 2. New plate cutting setting and welding inside lower and upper plate. 3. Pin hole oval worn out portion welding built up as per size. 4. Arm end collar gousing and

1.Repairing of the broken portion of the door assembly 2.Broken portion door gousing and welding by steel electrodes. 3.Lock bar and lock bar pin repairing. 4.Door hinges broken portion gousing and welding by steel electrodes. 5.New bushing fit

1. Repairing of broken portion of the door assly. 2. Broken portion door gousing and welding by steel electrode. 3. Lock bar and lock bar pin repairing. 4. Door hinges broken portion gousing and welding by steel electrode. 5. New bush fitting.

1. Repairing of the broken portion of the bucket door assly. 2. Broken portion door gousing and welding by steel electrode. 3. Lock bar and lock bar pin repairing. 4. Door hinges broken portion gousing and welding by steel electrode. 5. New bush

1. Ball of arm making it in original shape and size after taken out of ball from arm by gas cutter and developing of outer surface by welding and the making outer shape smooth by grinding and cracked portion welding by steel electrode.

1. Bill of Arm making it in original shape and size after taken out of ball from arm by gas cutter and developing of outer surface by welding and the making outer shape smooth by grinding and cracked portion welding by steel electrode.

1. Ball of Arm making it in original shape and size after taken out of ball from arm by gas cutter and developing of outer surface by welding and the making outer shape smooth by grinding and cracked portion welding by steel electrode.

1.Front damage plate cutting size 4X12. 2.New plate welding in place of damage plate by steel and low hydrogen electrodes. 3.Front ribs new plate bending, shaping and welding size 6X5. 4.Blade lower portion buildup with plate for cutting ed

1. Ball of arm making it in original shape and size after taken out of ball from arm by gas cutter and developing of outer surface by welding and making outer shape smooth by grinding and cracked portion welding by steel electrode.

Repairing of blade cutting edge and end bit broken hole and worn out portion replacement by gas set and resetting and steel electrodes depositing welding and grinding and hole making and supporting welding and HT bolt, nut with washer providing 70 no

a. The damage structure of the all four side of the cabin straightening, rusted portion of structure cutting and new M S Sheet changing and welding. b. The structure of roof of the cabin rusted portion cutting new sheet changing by welding.

1. Repairing of the broken portion of the bucket door assly. 2. Broken portion door gousing and welding by steel electrode. 3. Lock bar and lock bar pin repairing. 4. Door hinges broken portion gousing and welding by steel electrode. 5. New

1.Repairing of the broken portion of the door assembly. 2.Broken portion door gousing and welding by steel electrodes. 3.Lock bar and lock bar pin repairing. 4.Door hinges broken portion gouising and welding by steel electrodes. 5.New bushing fi

Repairing of blade cutting edge and end bit broken hole and worn out portion replacement by gas set and resetting and steel electrodes depositing welding and grinding and hole making and supporting welding and HT bolt, nut with washer providing 70 n

1) Ball of Arm making it in original shape and size after taken out of ball from arm by gas cutter and developing of outer surface by welding and the making outer shape smooth by grinding and cracked portion welding by steel electrode.

1.The Tank of oil cooler top and bottom cutting for cleaning of blockage tubes and after cleaning both tank aluminum welding. 2.The Tank of Radiator top and bottom cutting for cleaning of blockage tubes and after cleaning both tank aluminum welding.

1. Boom cracked portion gousing V making and alignment. 2. Box making in side the portion of boom and welding by steel and low hyd.electrode 3. Required plate cutting from grounded m/c 4. Plate cutting as per required plate welding, alignment

1. New damage plate cutting size 4 ft.X 12ft. 2. New plate welding in place of damage plate by steel and low hydrogen electrode. 3. Front ribs new plate bending shaping and welding size 6 inchX 5ft. 4. Blade lower portion development with

1. Ball of arm making it in original shape and size after taken out of ball from arm by gas cutter and developing of outer surface by welding and the making outer shape smooth by grinding and cracked portion welding by steel electrode.

1. Old rusted mud guard cutting by gas cutter. 2. New MS sheet cutting and making as per mud guard size. 3. New mud guard welding. 4. Angle welding in mud guard core. Operator safety glasses fitting 1. Front safety glass fitting size

1. Damage blade arm broken plate cutting in side lower and upper side-10 inch x 4 inch. 2. New plate cutting, setting and welding inside lower and upper plate. 3. Pin hole oval worn out portion welding build up as per size.

1.Front damage plate cutting size 4X12. 2.New plate welding in place of damage plate by steel and low hydrogen electrodes 3.Front ribs plate bending, shaping and welding size 6X5 4.Blade lower portion development with plate for cutting edge

1) New making of both rear transmission cover. 2) Plate cutting, shape making, welding. 3) Holes making by drill m/c. 4) Transmission cover fitting. 5) Sport L type making and welding by steel electrode. 6) Plate cutting from grounded m/c.

1. Ball of Arm making it in original shape and size after taken out of ball from arm by gas cutter and developing of outer surface by welding and the making outer shape smooth by grinding and cracked portion welding by steel electrode.

Repair, Maintenance, and Installation of Plant Systems/Equipments (Version 2) - Coal Mines; A Repairing of 01 nos impeller welding machining of 2500 GPM 120MH Kirloskar Pump SCT 200/58-2 and B Repairing of 08 nos neck ring outer inner welding machin..

1. Removing of broken nut with welding. 2. Complete dismantling of leaf spring. 3. Change of spring shackle.

1. Removing of broken nut with welding. 2. Complete dismantling of leaf spring. 3. Change of center bolt.

03 Nos. Rollers Periphery welding and machining of TATA Ex-1200 Sl. No. 70 Shovel of ABOCP Mines

REPAIRING OF BERCO MAKE 440 V WELDING MACHINE SL NO 1411 INSTALLED AT SUB-STATION OF BIRSA PROJECT

Repair / replacement of cabin safety glass, door handle after denting and welding of Dumper 2219 of Purnadih Project

For repairing of water tanker welding and painting etc. of BR17G- 0167 at Tetulmari Colliery under Sijua Area

For Complete repairing and rewinding of 50KVA, 600 Amp 440Volt welding machine at Nichitpur Colliery under Sijua Area

PILLAR, TRUSS, PARLINE, RIDGE, PPGL SHEET, ROUND PIPE, FASTNUT, FABRICATION, GROUTING, SHEET FITTING, PRIMER AND PAINT

For fabrication of drive drum of F.B No. 03 of Sendra Bansjora Colliery under Sijua Area

Dismantling of 30 Feet Long making and Errection , Fabrication gate at Entry Point of ROCP/SJ.