Fabrication Tenders in Jharkhand

Please Refer ANNEXURE B in Tender Document

Please Refer ANNEXURE B in Tender Document

Please Refer ANNEXURE B in Tender Document

a) Repairing of 02 set impellerwelding/machining of 4000GPM 100UPH8 b) Repairing of 04 Nos neck ring outer inner welding/machining of HT pump (Neck ring bush and distance pieces C) Sleeve making for over size bore of gear coupling at ROCP

Square Pipe Iron 20 Feet, Iron Angle 20 Feet, Iron Patti 20 Feet, Aluminum angle 20 Feet, Screw Bit 1 inch, Iron Cutting Blade 4 inch, Cutting Blade 14 inch, Welding Rod, Drill Bit Set Bosch, Acetylene Gas Regulator BOQ Title 40000

Rubber Sheet– 5 MM Neoprene Rubber Sheet size-1.0 MTR wide x 2 Mtr. long– 30 to 60 Deg., ELECTRODE MS 3.15 X 450 MM GRADE E6013; AWS A5.1, MS WELDING ROD 4 MM X 450 MM LONG GRADE E 6013; AWS A5.1

Repairing of BL14TH Tyre Handler with following works I) Dismounting of lift arm assembly and repairing it by cleaning , grinding, welding with suitable electrode and line boring and making of 02 Nos of steel bush and pin at lift arm foot and

1. Repairing of 01 no. adaptor and bit sub. 2. Adaptor and bit sub cutting by gousing electrode. 3. New thread making. 4. Adaptor and bit sub welding by steel electrode. 5. Over spreaded yoke portion cutting by gousing electrode. 6. Cutted

1) Link pin opening by gas heating and puller set-22 nos. 2) Deposition of material in worn-out link bore and making bore standard size- 22 nos. 3) Pin welding and machining-20 nos. 4) Special bush new providing-24 nos.

1.Damage bottom and side plate cutting. 2.New plate welding in place of damage plate by steel electrode/low hydrogen electrodes. 3.Ladder making/repairing. 4.Heavy duty valve with GI pipe fitting. 5.Socket fitting for delivery pipe. 6.Arrangeme

1. Dismantling of oil cooler assembly. 2. Cleaning of all tubes by gagging and HCL acid of oil cooler. 3. Soldering of leakage tubes of oil cooler. 4. Oil cooler foundation plate welding. 5. New rubber packing, bolt, nut and washer fitted.

(i) Repairing of cracked track frame and changing of under carriage and sprocket hole repairing work (ii)Repairing /welding of cracked brace arm 02 nos. and its mounting pin and repairing of RH Turnion cover its mtg. Bracket, broken bolt of turnion

1. Old rack segment removed by gas cutting and gauging electrode. 2. Grinding of handle body to remove burr from the surface. 3. Three layer welding of new rack handle and rack by steel joining electrode. 4. Repairing of dipper eye end.

For flange welding, carrying laying and jointing(vertical and horizantal) 8 inch dia MS Pipe 115 nos. bends 22 nos and 10 nos short piece (approx 700 mtr) a new delivery range for 4000GPM Pump for dewatering of quarry water at TOCP.

Repairing of cracked track frame and changing of under carriage and sprocket hole repairing work and repairing/welding of cracked brace arm 02 nos and its mounting pin and repairing of RH trunion cover its mtg bracket, brocken bolt of trunion cover t

Following repairing is to be done in Dumper SL Ne 60396 D 60393 and Dozer -T- 13275. 1.Repairing of differential link arm. 2.Repairing of worn out both sprocket ovel holes.3.Repairing and rewinding of 3phase 650 Amp. Welding machine air

Repairing of one leg including retaining wall/revetment of Loc. No.- 69 of 220 KV S/C RCP-Joda T/L and angle with stub welding in rusted tower legs, dismantling and re-construction of damage portion foundation plinth of 104nos. rusted leg

Repair, Maintenance, and Installation of Plant Systems/Equipments (Version 2) - Coal Mines; Repairing of 02 no impeller 02 no impeller shaft and neck ring outer inner and one set spare welding of 2500 GPM 120 MH Kirloskar pump SCT200/58 of Rajmahal ..

Leakage repairing of under ground inch domestic water supply pipe line as well as fabrication of 01 no Head End at Baludenga domestic water supply station for tanker filling re installation of pully over old shaft structure, GRD Project.

repairing work of Dumper D10304 1. Differential Link Overhaul Repairing of upper and lower differential links. Removal and refitting of bushes. Fabrication and fitting of 16 nos. of new pins and bushes 2. Removal of existing cross. Grinding and

A. Cutting and Dismantling 21FT x 21FT Pontoon n Fabrication of size 21FT x 21FT, installation of 2000 4000GPM Pump/Motor set with base plate on Pontoon B)Repairing of 2 nos of heavy duty MS Pontoon Size(20FTx25FT)

For towards fabrication of(i) pontoon of size 21ftX21ft (ii) Mannual pontoon of size 8ftX6ft (iii) Installation of 4000 GPM pump / motor set with base plate on pontoon at IV seam quarry of Sendra Bansjora Colliery, under Sijua Area.

Repair, Maintenance, and Installation of Plant Systems/Equipments (Version 2) - Coal Mines; Repairing of Top roller bracket and its related job and fabrication erection of deck plate frame portion in belt conveyor of silo section at Rajmahal CHP; Se..

Repair, Maintenance, and Installation of Plant Systems/Equipments (Version 2) - COAL MINES; Fabrication of Two number 120 Drum pontoon one for establishment and one for standby for establishing RKB Pump Kirloskar Make Wilo Pump MP Make on pontoon in..

Repair, Maintenance, and Installation of Plant Systems/Equipments (Version 2) - Industry Unit; Fabrication of 2 no of Blasting Shelter Size 4 ft X 5 ft X 10 ft with seating arrangement for safety section of Rajmahal Project; Service Provider

Complete Reapiring/overhauling of self-starter , alternator and FIP Pump silencer boX

Please Refer ANNEXURE B in Tender Document

Repairing/Overhauling of GEC Make 800AAmp OCB 440V Sl.No.40/0097 at Main Substn NPC(ii)Comp.Rep./Overhauling of GEC Make 400Amps OCB 440V Sl.No.30/0033 at Main Substn.NPC(iii)Fabrication and Installation of 2 Nos.of interlocking setup between AB

For fabrication of (i) Pontoon size 24X24 (ii) Manual pontoon size 8X6(iii) Base plate size 9X3.5 and (iv) Installation of 4000GPM pump/ motor set, with base plate on pontoon at IV seam query of Sendra Bansjora Colliery under Sijua Area.

1.Repairing of track tensioner assly of (LHS) track chain cutting opening and fitting etc work of L T CK 300E B168.2. Repairing of carrier roller and fabrication of propel motor guard etc work in Tata Hitachi ZX650 SL No-182

01. Repairing of propeller shaft its UJ cross guard railing and ladder and operator cabin front rear and both side safety glass with lock rubber bit changing fabrication guard Drill Sl 242. 02. Operator cabin front glass rear glass side glass

Repair, Maintenance, and Installation of Plant Systems/Equipments (Version 2) - Coal Mines; Fabrication of Two number one for establishment and one for standby of 96 Drum pontoon for establishing Complete set of 4000 GPM 10UPH8 Pump on pontoon in De..

Custom Bid for Services - Hiring of Diesel driven road vehicle ie MUV TATA PICK UP Xenon Yodha or similar of 1decimal 5 Tonne load capacity vehicle in good working condition including driver cost fuel cost maintenance cost consumable charges ... Diesel welding machine ... for welding safety ... by welding as ...

Engine Overhaul, Clutch Plate, Pressure Plate release bearing, Clutch cly assy, Slevee cly assy, Rotatory pump overhaul and Injector overhaul, Tail light Assy, Wiper blate arm, Rear brake booster, Gear box noise overhaual, Body welding, All suspension kit and Road Spring, Fly wheel Assy

Engine overheating head Gaskit, Water cooler, Clutch Plate, Pressure Plate realease bearing, Clutch cly assy, Slevee cyl assy, Rotatory pump overhaul Injection, Water pump Assy, Steering Pump, Tail light Assy, Wiper blade arm, Rear brake booster, ... Body welding

1. Safety clutch gear teeth 122 nos. build up by suitable electrode 01 no. 2. Safety clutch gear teeth build up portion machining 122 nos. 3. Safety clutch gear teeth new making by Milling machine 122 nos. 4. Gear pin new making and pin welding.

1. Drilling of broken portion of the driving wheel for development of the new lugs of the driving wheel. 2. Fitment of the steel pugs in the drilled portion of the driving wheels. 3. Development of the lugs by welding the pegs for making the

1.Broken boom foot both side gousing by electodes. 2.Boom foot both side cutting and settig. 3.Boom foot both side welding by steel and low hydrogen electrodes. 4.Oval portion of car body holes rebuilding, grinding as per pin size. 5.Body moun

Repairing of differential link arm with replacement of new spherical bushing nd pin providing 8 nos. and bearing place bore welding nd making for new bush fitting with material depositing of BH60M Dumper Sl. No. D-60390, D-60393 and D-60396 of AAD

1.Broken boom foot gousing by electrodes 2.Boom foot both side cutting and setting 3.Boom foot both side welding by steel and low hyd electrodes 4.Oval portion of car body holes rebuilding, grinding as per pin size. 5.Body mounting broken por

Removal distorted of roof from grounded EKG Shovel at Urimari Project and roof EKG 548 of Birsa Project by sheet and channel cutting, resetting them after hoist drum fitment and welding, after alignment making all work to be done at site and on the

1. Drilling of broken portion of the driving wheel for development of the new lugs of the driving wheel. 2. Fitment of the steel pugs in the drilled portion of the driving wheels. 3. Development of the lugs by welding the pegs for making the

1. Drilling of the broken portion of the driving wheel for development of new lugs of the driving wheel. 2. Fitment of the steel pugs in the drilled portion of the driving wheels. 3. Development of the lugs by welding the pegs for making the

Following repairing is to be done in EKG-5A, Shovel HMB-597, CIL No.-3014 of AADOCM, Dhori Area. (i)Repairing/replacement of central journal and its housing welding. grinding and G.M. bush fitting (ii)Opening and fitting of hoist gear box of EKG5A

Repairing of cracked track frame and changing of Undercarriage and sprocket (LHS) hole repairing work of BD-155 Dozer Sl. No. T-13642/CIL No. 3658 and Repairing/welding of cracked brace arm 02 nos, and its mounting pin and repairing of LH Turnion co

Repairing work of BD 355 Dozer Sl. No. 12098/ CIL No. T 3931 of AAD OCM Dhori Area. Repairing of cracked track frame and changing of under carriage and sprocket hole repairing work. Repairing /welding of cracked brace arm 02 nos. and its mou

1. Drilling of the broken portion of the driving wheel for the development of the new lugs of the driving wheel. 2. Fitment of the steel pugs in the drilled portion of the driving wheels. 3. Development of the lugs by welding the pegs,spline

1.Damage portion drilling and new thread making as per bolt size 30 nos. 2.Stack bolts removing by gauging and welding and making new thread as per size 3.Bally guard damage part straightening and fitting 4.Water pipe line repairing and fitting

Repairing of CK 300 Sl. No 772 with following works (1) Dismounting of boom and stick assemblies. (2) Repairing of H-frame and ring gear mounting base by cutting and welding. (3) Repairing of boom mounting foundation and boom foot eye holes by g

Please Refer ANNEXURE B in Tender Document