MS Structural Plate as per IS 2062 (Unit - Quantity) (Q3), Steel Chequered Plates as per IS 3502 (Unit - Mass) (Q3), Hot Rolled Steel Beam, Column, Channel and Angle Sections (V2) conforming to IS 808 (Q3) MSE Exemption for Years of Experience and Turnover No Startup Exemption for Years of Experience and Turnover No Document required from seller Certificate (Requested in ATC), OEM Authorization Certificate, Additional Doc 1 (Requested in ATC) *In case any bidder is seeking exemption from Experience Turnover Criteria, the supporting documents to prove his eligibility for exemption must be uploaded for evaluation by the buyer Do you want to show documents uploaded by bidders to all bidders participated in bid? No Bid to RA enabled No Type of Bid Two Packet Bid Primary product category MS Structural Plate as per IS 2062 (Unit - Quantity) Bid Number ( ) : GEM/2025/B/6276179 Dated : 27-05-2025 Bid Document 1/16 Time allowed for Technical Clarifications during technical evaluation 3 Days Inspection Required (By Empanelled Inspection Authority/Agencies pre- registered with GeM) No Evaluation Method Total value wise evaluation Arbitration Clause No Mediation Clause No Bid Details EMD Detail Advisory Bank State Bank of India EMD Amount 9778 ePBG Detail Advisory Bank State Bank of India ePBG Percentage(%) (%) 3.00 Duration of ePBG required (Months) ( ) . 3 (a). EMD EXEMPTION: The bidder seeking EMD exemption, must submit the valid supporting document for the relevant category as per GeM GTC with the bid. Under MSE category, only manufacturers for goods and Service Providers for Services are eligible for exemption from EMD. Traders are excluded from the purview of this Policy. (b). EMD & Performance security should be in favour of Beneficiary, wherever it is applicable., Beneficiary : ONGC MEHSANA Mehsana Asset, NA, Oil and Natural Gas Corporation Limited, Ministry of Petroleum and Natural Gas (Finance And Accounts Officer) MII Purchase Preference MII Purchase Preference No Details of the Competent Authority for MII Name of Competent Authority GGM 2/16 Designation of Competent Authority Head MCoDP Cell Office/Department/Division of Competent Authority PMC CA Approval Number PMC Circular no. 52/2024 dated 18.11.2024 Competent Authority Approval Date 18-11-2024 Brief Description of the Approval Granted by Competent Authority Notwithstanding anything contained elsewhere, procurement where the estimated to be procured is less than Rs. 1 Crore shall be exempt from this Order Competent Authority Approval for not opting Make In India Preference : View Document MSE Purchase Preference MSE Purchase Preference Yes 1. Purchase preference will be given to MSEs having valid Udyam Registration and whose credentials are validated online through Udyam Registration portal as defined in Public Procurement Policy for Micro and Small Enterprises (MSEs) Order, 2012 dated 23.03.2012 issued by Ministry of Micro, Small and Medium Enterprises and its subsequent Orders/Notifications issued by concerned Ministry. If the bidder wants to avail themselves of the Purchase preference, the bidder must be the manufacturer/OEM of the offered product on GeM. Traders are excluded from the purview of Public Procurement Policy for Micro and Small Enterprises and hence resellers offering products manufactured by some other OEM are not eligible for any purchase preference. In respect of bid for Services, the bidder must be the Service provider of the offered Service. Relevant documentary evidence in this regard shall be uploaded along with the bid in respect of the offered product or service and Buyer will decide eligibility for purchase preference based on documentary evidence submitted, while evaluating the bid. If L-1 is not an MSE and MSE Seller (s) has/have quoted price within L-1+ 15% (Selected by Buyer) of margin of purchase preference/price band defined in relevant policy, such MSE Seller shall be given opportunity to match L-1 price and contract will be awarded for 25% (selected by Buyer) percentage of total quantity. The buyers are advised to refer the OM No. F.1/4/2021-PPD dated 18.05.2023 OM_No.1_4_2021_PPD_dated_18.05.2023 for compliance of Concurrent application of Public Procurement Policy for Micro and Small Enterprises Order, 2012 and Public Procurement (Preference to Make in India) Order, 2017. Benefits of MSE will be allowed only if seller is validated on-line in GeM profile as well as validated and approved by Buyer after evaluation of documents submitted. 2. Estimated Bid Value indicated above is being declared solely for the purpose of guidance on EMD amount and for determining the Eligibility Criteria related to Turn Over, Past Performance and Project/Past Experience etc. This has no relevance or bearing on the price to be quoted by the bidders and is also not going to have any impact on bid participation. Also this is not going to be used as a criteria in determining reasonableness of quoted prices which would be determined by the buyer based on its own assessment of reasonableness and based on competitive prices received in Bid/RA process. Excel Upload Required : MATERIAL BREAKUP DETAILS - 1748327781.xlsx MS Structural Plate As Per IS 2062 (Unit - Quantity) ( 1 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Bid Requirement (Allowed Values) 3/16 Generic Mild Steel Plate Specification HOT ROLLED MEDIUM AND HIGH TENSILE STRUCTURAL STEEL conforming to IS:2062 latest Constructional Nominal Thickness of Plate 5, 6, 7, 8, 10, 12, 14, 16, 18, 20, 22, 25, 28, 32, 36, 40, 45, 50, 56, 63, 1.6, 3.15 (millimeter) Nominal Length of Plate 2500.0 (millimeter) Nominal Width of Plate 1250.0 (millimeter) Performance Steel Grade Designation E 250, E 550 Certifications Type Test Report OEM test Report as per specification for complete lot to be submitted along with the supply to prove conformity of product for declared parameters to the Inspecting Officer/Consignee by the Primary Producer Specification Specification Name Bid Requirement (Allowed Values) Additional Specification Parameters - MS Structural Plate As Per IS 2062 (Unit - Quantity) ( 1 pieces ) Specification Parameter Name Bid Requirement (Allowed Values)
Loading
Loading…